Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi Nordic,
I have decoded the advertise report below. Will you please confirm my understanding is correct.
Especially
[02] --> NUS_SERVICE_UUID_TYPE
[01] --> BLE_UUID_NUS_SERVICE...
Hello,
I am using the ble_app_beacon example on a nRF52840 dongle.
Without changing the code I am able to load and use it on my dongle.
Now, I am trying to add some...
Hi , i have attempted to build an spi read and write function for the BMI085 imu sensor and I seem to be having a problem with the read function. i have used the spi example...
Hi i'm studying ESB in nrf52833 DK
I have a few question.
1. When a packet is sent from ptx to prx, transaction starts, and when prx receives a packet from ptx, it sends...
Hi,
I want to add ble dfu to the hid keyboard example using nRF52810. I have tried unbonded and bonded，both are not work.
By using the bonded way, I made the following...
HI,ALL:
In SDK16, 1 .as topic,when I trigger the mouse_movement_send() and the mouse_click_send() at the same time, Error occurs.
2.how to detect BLE search device sucessfully...
Dear Members,
I tried to find a file *pca10056 project for bsc_rx on ant_plus ?
Can anyone tell me where I can find that file on the SDK ?
Thanks
Visit my lab...
We use a frontend that requires four pins and the timeslot API with our own protocol on nRF52832 & nRF52840. This works fine, but for BLE to work properly we need to leave...
i have a problem with the nRF52 DK (PCA10040) I followed these instructions https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3.1.pdf and the python version is 3.9...
Hi, I am using nRF Connect SDK 14.0 with nRF9160 DK.
I want to use nRF52840 as a controller and nRF9160 as host. To achieve this, I flashed hci_uart sample on nRF52840 and...
Hello!
I move my device from nRF52811 to nRF52820 ( QDAA-C00 ) and I have a problem when using a comparator and TWI
If I configure TWI0 or TWI1 and use it with external...
Good day,
I am using a DK board with the nRF52832 (pca10040) and I am using a 4 kHz buzzer connected to the gpio 16. I have seen the examples pwm_driver and pwm_library...
Hi, I am using the Nordic nRF52832, with the Segger IDE（Nordic）, and v1.4.0 of theSDK, and would like to know how to enable both LLPM and Multilink.
I am starting from the...
Hi.
I want to ask about the Queued Writes module and the NRF_SDH_BLE_VS_UUID_COUNT. In the example ble_app_uart, in the "services_init(void)" function we initialize the...
