Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am trying to interface the microphone with nrf52840 and using the PDM interface. After initializing the module (nrfx_pdm_init) and then set the buffer , I do see clock and...
Dear Sir.
I have some boards that work with nRF9160 and Chipsim.
Some work fine.
Using MQTT application
With two boards I get the errors.
ERROR: getaddrinfo failed...
I am new to the nRF5 SDK. This is my first time using nRFX SPIM so this may well be a beginner error.
I'm using SDK version 17.02 and I am using a nRF52840 module.
I...
Board: nRF52840DK
SDK: 15.3.0
Softdevice: 6.11
I am trying to increase the MTU size in order to read more data on the peripheral. I have tried to increase the NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
The SDK version I use is 15.3. And I tried to add the following code to the ble_nus.c
But it didn't work.There is no characteristic 0x2901. I don't know what's wrong....
Hi, I'm investigating the current consumption of a new product that we are developing and have found
current spikes of 40mA every 24ms. The spikes occurs in unconnected...
HI,
I get confused using the ble terms hence i'll try to articulate my query as much as possible. I'm using the nRF52832 board and all i have one service with one characteristic...
Hello,
I want know what is the difference between the three kind of low power mode?
System ON, Full 24 kB RAM retention, Wake on GPIOTE input (Event mode) System ON...
Hello
I am trying to get the angle of the sensor using the value of mpu6050.
I used a formula to obtain an angle using sensor values. However, if I calculate this expression...
Hi,
I´m using SDK v16 on a custom board and try to implement the wake up functionality of the low power comparator. In order to describe the system as clearly as possible...
Hello.
I am programming the NRF52810 breakout board.
Before I am testing the prototype, I am using NRF52832 breakout board, and it works well now.
However, the same...
Hi Dev Team,
I was working with the nRF9160 and started off with the basic UART sample found here : https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples...
Dear every body,
some days before, i raise an issue relate my fault at here: https://devzone.nordicsemi.com/f/nordic-q-a/68010/nrf52810-issue-with-32mhz-external-clock ...
