Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi ,
I am using the code that is built-in and I want to know about the Security manager. I want to see the encryption is enabled or disabled. What is the command? If I want...
Dear Community;
I am trying to read serial data sent by a PMS 5003 in hexadecimal. If I connect the PMS 5003 to a conventional serial device (Raspberry) this is what I...
Hi, I've recently updated to the latest NCS repo. I'm not entirely sure what version of NCS i was on before (perhaps if you could tell me how to check - as i made a copy of...
Hi, I am following the below link for creating custom services/characteristics. https://github.com/bjornspockeli/nRF52-Bluetooth-Course 1-I have added the notify part but...
Hi,
I am working on the MG996R servo and MG90S with nRF52840.
I am using the following delay logic to operate MG90S. (As per datasheet)
MG90S is working perfectly fine...
Hi ,
Just one question.
I am trying to create services using hrs examples and its useful.
Currently one question I have that ,
the battery indicator is only notifiable...
Using: Windows 10, nRF Connect v3.5.0, nrf v1.3.0, zephyr v2.3.0
I have a board based on the Thingy91 and the Asset Tracker application. I verified serial console output...
I want to quickly send up to 100KB of data to a connected smartphone and then disconnect to save battery.
I have most of this working using the NUS service but today I noticed...
Hi Team,
I would like to perform the DFU without using the nrfutil and OTA update. Is there any way to perform DFU without the nrfutil.
Our requirement is - We have...
Hello,
i built a SPI Master example based on this: SPI Master example
The example is a bit outdated and needed some rework and fix to work. I don't know if i am missing...
Hi.
NRF52832 is used as central for connecting with phones as peripheral. NUS service is used. Lesc is used too.
SDK 17 SoftDevice S132 V7.0.1
I have sometimes crash...
Hello,
From some time now i have been tryng to start developing an app, but i encountered a problem where the board does not connect, or does not find a provider from the...
Hi,
My goal: F lash hci_usb in my nRF52840 Dongle, so that i can use Bluez stack in my Linux host and nRF dongle as BT controller.
Build status: Success
Flash : Failed...
Hello,
I am trying to find the electrical and timing specs of the nRF52832 SoC. Where can I find them? In the Product Specification document they are not given.
Thanks...
