Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi,
I have a problem with a specific Zigbee certified device that I can't connect to my Nordic device.
When trying to connect to the device, I go to see the status:
...
Hi,
In need to debug my application using segger IDE when there is bootloader already present in nrf52832 chip .
The sdk we are using is SDK 15.3
Bootloader:- "secure_bootloader_ble_s132_pca10040...
Quick project overview:
Mesh network using nRF52840.
Nodes need to be able to be controlled individually (setting GPIOs) and also report back data (ADC, GPIO state) to...
Dear sir/ madam,
I have two questions regarding NRF52832 as follows:
1. Will nrf52 only get connected to apps provided by nordic? I want to it to get connected to serial...
Hi,
Greetings!
I am using following setup
1. Mesh SDK: 4.0.0
2. SDK 16.0.0.
3. Segger Embedded Studio on Windows 7
I had a look at "pwr_mgmt_pca10040 " example...
I slightly modified the qspi example code to try something that I'd eventually like to implement as part of my application. But when I try to interleave reads and writes then...
Hi,
We did stumble upon an issue with our BLE peripheral running on an nRF52832 with Softdevice S132 5.0.0 . The central side is implemented on top of the UWP (Universal...
Hi. I want to run the pca10059 dongle so that the BLE is in central mode and is recognized as a virtual port on the pc. Is it possible to operate with only UUID settings in...
Hi, I recently bought some nRF52 DK rev 2.0.0 (2019.25) boards from a US-based distributor. The distributor seems to not be in the loop on the specifics of the design, as...
How do I use the device root key to encrypt and decrypt?
I can set the device root key in the cryptocell register, but not sure how to use it. I am using Zephyr by the way...
Hi, nordic engineer:
Our project has a function, that is, BLE+Thread coexists. We hope that the mobile phone can upgrade the device through BLE. Can this idea be realized...
Hi All
Now I am testing the example code \examples\ble_peripheral\ble_app_uart with Nordic nRF Connect app on smart phone. i do a limit change in function uart_event_handle...
Hi,Master:
Platform: nrf52840
Bluetooth protocol stack: s140
When using qspi to communicate with external flash (communication speed 32M), occasional qspi communication...
Hi,
I have been working with different boards to implement different ML TensorFlow Lite samples in the 52840. I used Particle and Arduino BLE Sense.
All forks from the...
