I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello, I'm trying to get an ANT+ peripheral example to work on an Adafruit nRF52832 breakout module. I'm using the 15.0 SDK, SD S212 and SES with a J-Link to program over...
Hi,all,
Now I am using nRF52832 to develop a Tire Pressure Monitoring System ,but I serached the ANT website and found that " a TPMS profile is "in the works". ANT+ members...
hi
i need to test the BT OTA test ( total radiated power (TRP), total isotropic sensitivity (TIS)
https://www.mwrf.com/test-measurement/ble-antenna-testing-helps-optimize...
Hello, maybe my answer didn´t get to you correctly. Referring to my post 10 days ago, I am still stuck controlling the joining procedure .
https://devzone.nordicsemi.com...
HELLO
I would like to know how to test RF for nrf24l0.
Of course, the RF test I'm talking about is frequency modulation for KC certificate
Previously, nrf24le1 was...
Hi,
Just to be clear, you are looking for reference DFU controller firmware for the Host MCU, in order to upgrade the firmware on the nRF52832。
I also need this feature...
Hello Developers,
I have configured a mesh network where I have a gateway node and multiple relays to relay messages from End nodes (sensors)
My question is the following...
Hi. I am working with nrf52832 trying to get Bluetooth and UART and a I2C peripheral working at the same time. I had a working version of the I2C peripheral and UART working...
hi.......
i need to run the program continuously using timer ......and want to check the data every one minute how to do that
i have seen timer example .. i am confused...
I am using nRF 5 SDK v 14.2.0.
I'd like to change the tone of the buzzer, how can I do it?
I'd like to make the following three settings.
Treble (+ 1 kHz), normal (+0...
HW: nrf52840
SW: nRF5_SDK_15.2.0_9412b96
source code: blinky_rtc_freertos example
Q1:
I read freeRTOS xtaskcreate operation on the web, it seem that I just need to...
Hi,
I am using Segger IDE.
I encounter error undefined reference to `nrf_drv_rng_init' .
I have include the below header file;
#include "nrf_drv_rng.h"
I already...
Happened when I occasionally compare the NRF_TWIM_Type struct in nrf52.h with the TWI registers (table 127) in nRF52832 Product Specification v1.4, there are many differences...
Will there be an HTML version of the nrf52832 spec document?
I hope Nordic is not expecting me to manually browse through a 550 page pdf document. I regularly use the infocenter...
