Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I use the SDK15.3.0.
(nRF5_SDK_15.3.0_59ac345 -> example -> ble_peripheral -> ble_app_uart ->pca10040 -> s132 -> ses)
The default baudrate of uart is 115200bps...
I used SEGGER Embedded Studio ARM 4.16 to by mistake program a NRF52-DK PCA10040 with a PCA10056 example from your SDK collection. As a result, I now persistently get "Failed...
Hi,
I'm developing multiprotocol applications based on examples from Thread SDK: Proximity/CoAP server and BLE UART/CoAP client. All CoAP communication in this examples...
SDK version: 15.3
Soft-device version: 6.1.1
Hi,
I've been working on a low power application where every 10's of uA is important. My application requires SPI as...
Can you provide documentation of the energy costs for creating/verifying ed25519 and NIST P-256 signatures with the CryptoCell CC310 peripheral found on the nRF52840 device...
I am trying to set pins when I press a button, and clear is as soon as I stop pressing the button, however the board turns on all leds at once and does not respond to input...
I came across this old thread, which asks the same question, but was abandoned by the OP ( ) without follow-up:
https://devzone.nordicsemi.com/f/nordic-q-a/26699/52832-saadc...
Hello,
I am looking into migrating DFU and Bootloader over BLE from SDK v15.0 to SDK v15.3. I have a few questions about the code changes which I was hoping I could get...
I was reading about Mesh DFU and noticed that when it happens, the receiving node will rebroadcast it to all devices within radio range. It seems like devices will pick up...
Hello all,
I am trying to adjust the current consumption of my device based on nrf51822 s130.
A have read the https://developer.apple.com/hardwaredrivers/BluetoothDesignGuidelines...
I wrote some user data to 3rd party nrf52840 boards flash using the command "nrfjprog --memwr 0x1001084 --val 0x33333333" , when I ran the program the data values was not...
Hello,
I want to test the mesh provisioning demo with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo
I have encountered...
We are using an NRF52840. After initializing a UART that uses P0.06-TX and P0.07-RX the following function calls fail: sd_ble_gap_device_name_set() and nrf_sdh_enable_rquest...
I am playing with the TIMER peripheral and I am seeing that I must call the function "nrf_timer_event_clear" in order to get the TIMER interrupt to stop firing once a COMPARE_EVENT...
