Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
So I am aware the nRF52832 utilizes the ARM cortex M4 microprocessor and has 32 configurable GPIO, but I'm failing to find how to access the registers controlling...
Hey I am trying to setup UART on my Thingy52 but when I’m trying to compile my project I getting this error message:
I am using GNU Tools ARM Embedded 4.9 2015q3 for compiling...
Updating all components with the nrf9160DK, I am unable now to run the LTE/BLE Sample. I built all the prerequisites, secure-boot, hci-uart and lte/ble sample however, the...
I am very new to Nordic boards, so my apologies first for my ignorance.I recently bought Nrf52840 boards and I want to build a very simple Bluetooth mesh application but I...
Hello All,
As we all know Segger Studio is not supported by SDK12.3 by default. Porting to Ses is easy and help is available but it is for basic programs. if we want to...
sdk version:15.2.0
sd version:6.1.0
platform:pca10040
I have inited three saadc channels , I want to close the specific saadc channel ,but error occured .
The...
Sir,
Using nRF ToolBox for Android.
Our ble device using one of your ble chips sends bytes 0x02, 0xBA
But nRF ToolBox UARTService.java function onDeviceConnected( BlueTooth...
Hey all, my QSPI woes continue. I'm trying write 4 bytes (0xDEADBEEF) of data to a flash chip, equivalent to the NRF52840 DK. I'm using PP4IO and 24 bit addressing mode but...
Hello,
I am using the NRF_LOG_INFO macro to print certain event results. I am writing a large chunk of memory over I2C. The operation succeeds but the log print is only...
Hi All,
I' ve successfully programmed an nRF52840 device with an application running with PHY_CODED modulation and I can scan it from my Samsung Galaxy S+. Unfortunately...
Hi, I'm running nRF5 SDK v15.2, and tried to run the led softblink example on port 1 of a nRF52840, which did not seem to work. I found a problem in low_power_pwm.c, which...
We want to use some device in the peripherial mode.
after the devices were bonded, for next connect I need to hide this advertise packet from air in the nRF Connect util...
We have a problem that we thought was isolated (affecting only one phone) until recently we started getting more phones exhibiting the same issue.
We are Australia based...
I can pair and bond as a Zephyr central via bt_conn_auth_register & bt_conn_security().
When the bond is successful I get a callback to cb_pairing_success(struct bt_conn...
