Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
hello, i am using nrf52 dk .I was testing example twi scanner.I want to read slave address.So i am using twi scanner example but i got error message as follow:
TWI:INFO...
Hi, I'm new here and I use nRF52832 (pca10040), I was wondering if it is possible to change a function in C / C ++ language during the runtime, that is, my idea is whenever...
Hi,
I had a problem using your (nRf's) implementation of block device with my flash memory (I think that exact model is not relevant here). I'm using SDK 15.2 with NRF52840...
Hi,
Do you have a declaration of conformity for the chipset nRF52832 ?
I need this document to justify to my laboratory the conformity of the Bluetooth module to the standard...
hi,
I have some questions, please help me solve these questions. ( I use SDK 15.2.0 and nRF52832)
1. my customer ask how many central bonded with one nrf52? (my project...
Hello,
I am trying to send data from my light switch mesh client (nRF52840) to my gateway, the nRF9160 using UART. I added the UART functionality to the light switch client...
Hello there,
I followed all the steps in the following link:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52%2Fdita%2Fnrf52%2Fdevelopment...
My device (nrf52832) has two signals triggering GPIOTE interrupts. I need to be as low power as possible, so both are setup to not use hi accuracy, making them share the PORT...
i need a help
As mentioned in this thread
https://devzone.nordicsemi.com/f/nordic-q-a/18512/directed-advertising-with-pre-shared-irk
in need to do directed advertising...
Hi,
We want to measure our external custom board which is not based on nRF52 chip. That board has current consumption header and it's chip draws maximum current of 60mA...
Hi:
I find a odd question when i use SES to develop nRF52832, ESB protocol is using and i need to config some different slaves with same code except the pipe num, i define...
Hello,
In my current zigbee project I have a sensor end device which should sleep when possible. I am handling the ZB_COMMON_SIGNAL_CAN_SLEEP event and have added zb_set_rx_on_when_idle...
Hi,
I am using NRF52 SDK version 15.3, Segger Embedded Studio.
I am using the ble_app_beacon example in examples/ble_peripheral, I have programmed 2 devices with the...
We are attempting to replicate the background DFU process presented in the example DFU over TFTP. Reference SDK that we are using is 15.2
What we do:
- We are trying to...
Hi,
While using the BLE advertising module, it struck me that it automatically stops advertising as soon as a device connects. This is not acceptable in my application as...
