Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
We am using nrf52840.The SDK is 15.2.0.I successfully combined usb example code with buttonless dfu. I could update more than once and it worked fine.
Depending...
Hi,
I have a working system based on NRF52832, SD132 and SDK 15.0. I am working with with the default MTU as my data requirement is low and everything is working great....
Hi i am using SDK15.2 nrf52832.
What is peer id? Which function is adding device mac address to whitelist? how does the whitelisting process implemented in HID example code...
In iOS, I have developed one sample code for BLE scanning and connection with peripheral.
I have one nRF51822 Ble. It has secure pairing mechanism. (Claimed by Hardware...
nRF52, SDK15, S132
Hi! After few days work I have stop scan from my central device on the nRF52832.
I can't to understand reason of this. But I need to know is scanning...
I downloaded sdk15 for nrf52832.all sample programs and soft devices are working fine but boot loader coding is showing some error. I am using this bootloader code install...
Are there example scripts to take readings or communicate with other devices over serial? Like, if I attach a temperature sensor, distance sensor, etc, I want to read from...
Hi there
I was going through the errata sheet and discovered the PAN #88.
It states that the current consumption is increased when entering System ON Idle within 125us...
If I just comment-out battery_measurement_init() in main():
Advertising does not start, I see nothing on the UART CLI, and the RTT log just shows:
With battery_measurement_init...
All examples shipped with the SDK have the same compile problem
components\libraries\util\app_error_handler_keil.c(47): error: A1198E: Unknown operand
The offending line...
Hi to all,
i had developed an app for PCA10056 and now i want port it on PCA10059, there is any guide or white paper that indicate how can i done that??
i read in the...
I've just started evaluating the nRF52840 DK and running into an issue when attempting to run any of the multiprotocol ble_thread examples.
I've downloaded the "nRF5 SDK...
Hi
I'm using the NFCT peripheral of the nRF52832 Rev. 1.
What is the intention of the LOCKDETECT field in the FIELDPRESENT register? I don't understand the description...
I can't connect to my nRF528540-DK anymore after I connected an external power supply and switched SW10 to off. the external power supply is 5V. my DK doesn't show up in device...
