Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
Currently, I am using the SDK15.2, BLE and two nRF52 DK boards, one using SPI master, and the other being the SPI Slave, between the SPIs and SPI master I added an...
Hi ,
I have one 128 bit base UUID something like
{0x07, 0x89, 0x1a, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa,
0xaa , 0xaa, 0xaa, 0xaa, 0xaa, 0x8a, 0xe1, 0xbc } ;
And custome...
I am prototyping something using the nRf52840 USB Dongle.
Dongle works with the power supply from the USB
BUT doesn't work by applying power to the VBUS and GND even-though...
Now I want to add apple media service, but the ram left for me is a bit small. My project is based on the nordic ancs example , and the ams and ancs is almost the same. So...
Hi,
I wonder if there exists a debug bootloader for thread examples. There is a bootloader in the secure DFU example, but it is not for debugging. "examples/thread/dfu/bootloader...
Hi All Techies,
IDE : Segger embedded studio, version : 3.40
SDK: nRF5_SDK_15.0.0_053641a version : 15.0.0
Mesh SDK : nrf5SDKforMeshv220src version : 2.2.0
computer...
Once my SPI code worked in the master SPI example, I editted a ble_uart example from the SDK 15.2 to include the SPI data transfer code. But I seem to run into issues with...
Hi,
We have designed a custom PCB using the nRF51822_xxAA and followed the reference design.
- The board works on 3.3V supply. 16MHz crystal used.
Only LED blinking...
HI,
I got a thingy 52 in the Nordic Tech Tour in Barcelona.
The first time I switch on I connected through my phone, but after switching off and try again to get connected...
Hi All, I had connected JLINK BASE on the target hardware which is having NINA-B301 chipset having nRF53480 core. When I am connecting the JLINK on the 10 pin connector on...
Hi . I have query about that in the target environment we are using NINA-B301 which us having nRF52840 chipset. Now this chipset is interfaced using USB in the target hardware...
Hi,
I just learned how to do a OTA DFU. I tried it with nrf52840 DK and was successful in it, but our custom board does not have a button on it. In production we will like...
Hello,
I have to evaluate I2C functionality of BL654 module. There seems to be RTC chip in Laird DVK BL654 board. Is there somebody how has investigating how does it work...
Hi everyone,
I have a custom board with a nrf52832 and a I2C device connected to P0.21 (SCL) and P0.20(SDA). I was trying out the twi_scanner example and had modified the...
Hello,
Is there someone who has worked recently with nRF52840 and SHT21 (Humidity / Temperature) sensor ? I have to do some basic test for HW and validate that sensor...
