Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi
Newbie in the nRF family of products so i might have missed the answers to my questions somewhere in the documentation and forum. if so i apologize.
I'm trying to get...
Hello ALL,
I have been using UART module and fstorage module in an application. I've been sending a bin file from PC to NRF52 using UART but when I tried to save it using...
Hi All,
I have some code that I'm porting from a Zilog platform over to the nRF52 platform. The code uses 1 timer and 1 uart. The goal of the code is to handle RS485 messages...
I am testing the IoT_lwip_MQTT_publisher_pca10056_s140 example project from SES on Windows.
I build and install the kernel with 6LoWPAN module on the Rpi3!
I can run from...
Hello，I'm from China。
At present, there is a need to broadcast beacon data in nrf51822 (SDK_12.3.0_d7731ad is used as the protocol stack version, and the...
Hi
I want to generate two PWM signals that are phase shifted with 90 degree, with similar duty cycle. I have the following pwm configuration, but I don't know how to proceed...
I am operating as a Central. How do I register and enable a discovered characteristic's indication?
I do the following and the subscribe passes but then the kernel crashes...
I'm planning to buy a nRF51822 based module for my BLE project & I wanted to know whether any of the nRF51822 based modules come with OTA ready bootloader out of the box....
Hi,
I'm trying to save sensor data to sd card on low power mode. When i connect to bluetooth mobile app can pull all data from sd card.
How can make this architecture...
Hi,
I'm using Nordic BLE Sniffer. When I look into the captured data I see a lot of malformed packet (CRC error). It try to decode any received data even if there is CRC...
I was digging around a bit in my code to get a better grip on logging. In sdk_config.h, I have the following relevant settings:
My modules all implement their own logging...
I am going to implement DFU over BLE in my nRF52832 project. Since the size of my application + softdevice larger than half my memory size I wonder how the update is performed...
We're looking to use the nRF91 to measure the LiPo battery voltage to determine battery health. We would want to know what the accuracy and range of %XVBAT is. Looking at...
I am trying to create CTS server using nRF 52840 dongle and nRF Connect PC app (v2.6.1). Currently I can manually provide current time and local time information to the app...
