Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi I want to ask about the best way to handle a lot of incoming bytes via UART on the nRF52832 (SDK 15.0.0). Unfortunately, the parsing of incoming data seems to be slower...
We are moving from using the Device Manager to the Peer Manager.
We are concerned about side effects concerning updating customer device firmware. One issue of concern is...
I stumbled upon Nordics video on facebook where they show how to calculate the distance between two NRF52840 Dev Kits. Link to video and article: devzone.nordicsemi.com/....
I downloaded version 15.2.0 of the nRF SDK. It contains the softdevice version 6.1.0.
I then attempted to upgrade to the softdevice to 6.1.1. After downloading the softdevice...
Hello,
What are the steps to recover a bricked nRF9160-DK? I want to get it back to the state that it was shipped in. I would assume refresh "secure_boot" and an app such...
Sir,
I have one custom MDBT50Q evaluation board and a ST-Link debugger. As the Keil IDE is fully defaulted to J-Link none of the example programs are building and flashing...
Hardware:Two nrf52840 DK Software: SDK15.2
We have 2 development boards acting as a master and slave communicating over UART. We are using the serial library for this application...
when i use the official example in nRF5_SDK_15.2.0_9412b96\examples\peripheral\blinky\pca10040e\mbr\iar using IAR IDE,
after building successfully, i failed to download...
Hi:
I use the new Mesh SDK 2.2.0 to make a demo.and I use the proxy_server and proxy_client example. now，I test and find the proxy_server example don't open the relay function...
Hi,
When I go through the code of light switch example, I am confused about relay functionality.
Compare with the v2.1.1, I can find the m_relay_enable in network.c but...
Hello!
We are currently developing a software solution which integrates many protocols into one Gateway. One of the protocols is Zigbee, and since it is the first time we...
I'm running FreeRTOS with SDK version 15.0 on nrf52 custom board.
I have two sensors, say A and B, on two separate SPIM bus instances. Sensor B utilizes PPI to trigger data...
I've been working on using an nRF52 as a host for a PS/2 synaptics touchpad mouse (to integrate with BLE HID). I was able to get a correct mouse position using two GPIO pins...
Hi,
i am using oled ssd1306 i2c with nrf51822. I am using peripheral mode and SDK v10.0. i choose this sdk version because of length i want to sent at one go that is 1024...
Help pls, i can't build a project.
Building ‘temp1’ from solution ‘temp1’ in configuration ‘Debug’ 1> Generating linker script ‘temp1.ld’ 1> Linking temp1.elf 1> Output...
