Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
We are developing a game controller with the nRF52832 and I'm keen to make the device also USB compatible via the CP2102.
We are using Segger Embedded Studio and have the...
Hey Guys,
I'm totally nooby, maybe you can help me. Following Problem:
I got a SparkFun nRF52832 Breakout Board and use the Arduino IDE to program it. Now i want to...
Hi guys, hope all is well. I was hoping someone could help me out with this particular issue. Maybe someone on here has tried to do the same thing.
Just some background...
Connectivity board crashes after a few seconds of sending/receiving packets really fast with the following:
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at ../nrf_sdk/components...
NRF52
I have a Transmitter and Receiver. The Receiver starts and listens to the ESB.
The Transmitter starts, sends a message on the ESB and restarts. The message is static...
We are in the progress of finalizing our first Bluetooth products, based on nRF52840, S140 6.1.1 and SDK 15.2.0. We have gone through the listing process (Launch studio and...
DFU failed on nrf52832 with my custom program that is based on coexist example and not failed with blinky ???
is there any frame loss for a big hex file that want to dfu...
Folks,
Using the HID mouse ble-peripheral example code as a base, I'm attempting to add SPI support, using the SPI example for pieces of code.
Both sets of code build...
I am trying to set up ack in my PTX so that when my PRX is off or out of range I get the case TX_FAILED event and when it is on and receiving data my PTX will get the case...
Hello,
I am looking into the nRF9160 hardware. And at the moment we are only interested in the lowest level possible.
The peripherals are well documented, as espected...
Hello,
I am working on TWI master application on a nRF51 board, with a sensor associated.
I have often a problem while the reception sequence.
My application:
-> nrf_drv_twi_tx...
The latest changes to the Secure Boot sample main.c file cause compilation issues;
new main.c @line 304 NRFX_PERIPHERAL_ID_GET(NRF_P0), 0);
Doesn't work.
old main.c...
SDK 14.2
nRF52832
The application I'm developing uses the flash memory to store parameters such as calibration parameters for the sensors on the product. I foresee that...
I start with the ble_template example (SDK 15.1 || nrf52382 || Embedded Studio for ARM 3.41). My goal is to transmit data (string or int) from a custom made PCB to the NRF_TEMPLATE...
Hi
I am back on the firmware end of my project after several months doing the PC and Xamarin ends in C#... Trying to remember my C...!
My device has 3 MCU's incl the...
