Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Dear Colleagues,
I am not sure whether TEMP anomaly 31 is applicable to nRF52832-QFAA-0B (NRF_FICR->INFO.VARIANT == 0x41414230)
nrf_temp.h @ 65 says:
static __INLINE...
A happy new year everyone,
I should develop a mesh sensor network for Raytheon Anschütz GmbH in Germany but I am an absolute beginner on Zigbee and therefore struggle a...
I have a BLE project that I wish to add Zigbee to (non-concurrent, if that matters). The project is built on FreeRTOS with several threads, using SDK 5.2.0 and S140 6.1.1...
Hi,
I am using nRF52840-DK evaluation for testing a Mesh configuration. I was able to successfully establish a mesh connection with a onoff-sample from zephyr and was able...
I am working on the project with radio transmitter(NRF24L01+) and receiver(NRF52840). I need to receive data at the rate of 250kbs. I tried to receive but it fails always...
Hello,
I want to interface a microcontroller with the nRF52832 chip in one of our designs. The microcontroller will be running on FreeRTOS.
I would like to know a few...
Hi,
We are currently in a testing phase of our software where we use an nRF52832 for extended advertising and an nRF52840 for scanning that has a scan interval and scan...
Hello, i´m trying make DFU with the Light switch server with the GATT and Proxy Enable, however in the process of update, i got this error in the device what receive the update...
Trying to lower uC current consumption to minimum
Im trying to remove features from my program
I've notice that removing the adc initialization actually get the current...
Hi All
I mount a minimum system for test BLE. I download a blinky program to the NRF52810. If I download a blinky without BLE version , it works well . But if I download...
Hi dear Nordic engineers and enthusiasts,
I am currently testing and researching on the functionalities of Nordic Thingy 52 in Bluetooth Mesh . I have tested with the provided...
Hi
I am trying to use the TWI on nrf52840 but i am unable to get it to work. its getting stuck somewhere. I dont have a logic analyzer so i am unable to check if the signal...
Hi,
I'm doing some experimental evaluation of BLE Long Range. I use the ble_app_att_mtu_throughput example with parameters:
ATT MTU: 247 bytes
Data length extension...
I am trying to test out the whitelist that I have created for the nrf52832 client. I have edited the whitelist so it will only allow one device to be bonded and added to the...
