Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Installed nRF5_SDK_15.2.0_9412b96 and nRFGo Studio. nRFGo Studio fails to recognize the nRF52840 DK board. Screen like this:
It sees and correctly identifies the Segger...
I am trying to do things like
get the current date and/or time
configure a socket
activate a socket
Usually I use commands like
at+cclk
at+csdf
at+ctzu...
I am following the Thingy:52 "Compiling With Keil" instructions provided in the following link.
nordicsemiconductor.github.io/.../firmware_compile.html
However, I get...
Hi,
We have released multiple products with the NRF52832 chip with SDK's ranging from 10.x to 14.x, quite successful so far.
However, one part that is lacking in my opinion...
I have been struggling with getting nrfjprog working on CentOS 7.x. Each invocation results in the following error due to the version of glibc used to link the nrfjprog binary...
Hello!
A quick question about how to shutdown unused RAM on the nRF52810-CAAA?
We're not using any of the Soft Devices. Our code is pretty tiny. Map file attached.
We...
Hi,
I want to read data from my ble UART (NUS), to do that I implemented the NUS service and registered the onDataWritten callback (which is the MBED equivalent of the HVX...
Hello:
If we are to use the nrf9160 in a production product, what additional certifications are required? For example, if I purchase a Telit cellmodule, I still have to...
Hello All,
I want the DFU service at the application level, not at the bootloader level. Means I have to build a very simple bootloader but I want DFU service at the application...
Hello nordic:
nrf52832 how to control pa, i use this functio pa_lna_assist(). This function is the solution on BBS.this used for s132,but i use s332.the ble is ok,but the...
As per description, I don't understand how to make a dfu package that writes the whole MBR+Application range and doesn't use a SoftDevice, for example out of a hex file such...
I'm using SDK 15.2 and trying to set up a USB mic class. I am having trouble getting the SOF audio interrupt to fire.
I initialize the app_usbd module with the configuration...
Hi
I would like to know that is there any Blue tooth low energy relay like RFID tag , which can detect bLE only and can trigger a circuit. It should have small form factor...
Hello everyone , i have noticed that the sniffer can pick up the the packet from the same channel twice.
According to the Bluetooth 4.2 specification, the advertisement...
Hi all,
We were developing our application using nRF52840 and later decided to change to nRF52832 considering our hardware constraints. nRF52840 has 16 bit counter for EasyDMA...
