Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Respected nordic community,
I am working on one project where right now i try to make custom service read operation through nrf52832 in segger studio. From my device(mobile...
HI, I am seungwoo
I am developing data transmission using nrf52810.
A 300-kilobyte file is divided into 220 bytes and transmitted continuously.
11-27 17:24:24.416...
Hi,
I'm developing a unit which i need from time to time to send a packet throw I/O lines (F.E.virtual uart)
However the packet bit timing is very critical.
As far as...
Hi, I am using nrf52832 with SDK 12.3.0 and nrf 52 dev board. I am experiencing a problem whenever I programmed nrf 52832 using nrf52 dev board and NRFGO, after certain number...
Hello, I'm currently using the nRF51DK with Wireshark as a BLE advertisement sniffer. So far this setup has worked great, but I'd like to make a small modification for development...
Hi all,
i am currently working on 5 nrf52832 DK boards, i want to use nrf mesh for indoor positioning system. I am currently using nrf sdk v15.0.0 and nrf mesh v2.2.0. ...
Hi.
We are on early phases of getting UART DFU support for our product. However I seem to run into communication issue with the bootloader even with the examples provided...
Should the DEBUG compiler flag be removed before flashing a board that should enter sd_power_system_off? I've seen some troubleshooting guides mention that Debug mode can...
I have set up the thread border router. I connected the NCP (a nrf52840) with a usb cable to a raspberry pi. Now I wonder if it is possible to connect the raspberry pi with...
Hi all,
Currently, I am working on Nrf52 DK with nRF52832 on Keil IDE. My focus is MQTT with 2 nRF52s and RPi. I have succesfully used examples in SDK, but now I am trying...
Hello,
I have got new rigado-301-A-R module, I want to know following things as I want to work on linux and i have a custom board just like rigado 301 eval board.
1. Procedure...
I have an embedded platform running JerryScript. Now, I need to add BLE functionality to it. The BLE module (connectivity chip) will be used is nRF52840. For this, I guess...
I’m trying to program a custom board with nrfjprog, but cannot get it connected correctly. (Connection is standard SEGGER cable, segger mini edu)
nrfjprog -f NRF52 --halt...
hi ，i have a problem! how to slow down the update speed when bootloader receiving the pack. my project is base on the SDK 15.2.0,s112 ,secure_bootloader example ,nRF52810
Dear nordic,
i want to create a low power current consumption ADC. i don't need adc value in every time. my need is just take adc value and disable it.
whenever i want...
