Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi Great Nordic team:
As title, when I perform white-list function in BLE connection,
Is there any way to know from peripheral that there is a connection request from...
Hi,
I have a project that I have product which I have produced several thousand over the last couple of years and today find an issue.
The product has a receiver that...
Hello,
Device: nrf52840DK
Software: nRFgoStudio (version 1.21.2.10)
Operating System: Windows 10 (updated)
I am not able to enable the reset pin. I am trying to...
Hello All,
I am trying to build the "bootloader_secure_serial" example from SDK 14.2.0 on IAR Embedded Workbench IDE ARM- 7.60.1 and I get this error: Error[Pg004]: macro...
Hi,
I'm trying to utilize PPI system to generate repetitive sequence of tasks (lets call them Task A, B, C, D, E, F) at 0,10,20,40,60,80 ms every second. i.e. I need to...
Hi,
I'm trying to test adding my own custom service, but have errors when I tried to add a 128bit UUID, the test code is simple, in the service_init() function, I just added...
I am using nrf52832 and sdk 14.2.0.The software I am using is keil 5.17.the error is as follows:.\_build\nrf52832_xxaa.axf: Error: L6915E: Library reports error: __use_no_semihosting...
Hi,
In nRF SDK15, Bluetooth peripheral examples for HID devices were limited to keyboard and mouse. By any means, can we configure Nordic device as a game controller?
Hello,
I am currently learning the PWM peripheral of the nRF52DK and am a total beginner in PWM.
I have tried running the attached program and this allows the LED0 to...
Hello,
I am working on a project which requires radio transmitter and receiver to work in sync with the SPI. So the setup is as follows the Transmitter transmits a signal...
Hi,
I am trying to write my own dfu updater for the NRF51 chip and I am stuck trying to make sense of the actual DFU sequence described here infocenter.nordicsemi.com/index...
I am trying to set up mqtt between 2 nrf52s and rpi3 with the examples of sdk 15.0.2. I am very new to nrf52, rpi3 and networking. I have read everything needed as much as...
Let's send a string over UART. RTS signal will go low (active). So far, so good.
The problem is that RTS remains active even after sending is done. And because it is still...
I have two boards. I ran the exact same commands on both boards. The commands flash the same bootloader+app+softdevice+app settings hex file. One board reboots into the application...
Hello,
Setup: Running Ubuntu 18.04 inside Windows Host (using VMWare).
Device: nrf52840DK
Operating System (used for development): RIOT
I would like to communicate...
