Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I have recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. To begin, I used the "Hello World" sample code. While I was able to successfully build...
I have searched everywhere and can't find a working example that shows how to create a new BLE ID and save it to the setting s partition.
Please show me the configurations...
I am incorporating the nrf52840 into a new design and it is my first time working with a Nordic product. I am looking to start with the SEGGER J-LINK EDU MINI due to it's...
Product: nRF54L15DK, SDK V2.9.0
Application: Multi protocol (BLE + Matter/Thread) Door Lock
Issue: BLE bonding is not retained after power cycles. The mobile app requests...
Hi,
I am debugging the zigbee functionality and would like to enable the zigbee log,already enabled log in prj.conf but no data coming out.What do I have to do to enable...
i am unable to build the unit test code with kernel file
FAILED: CMakeFiles/testbinary.dir/home/avinash/zephyrproject/unittesting/gce-source_code_latest/app/vipr/model/gas...
hi Nordic teams:
we meet one serious issue about LSM6DSL FIFO reading, our product (host mcu is nrf52840) need to read lsm6dsl FIFO data periodically with one second interval...
We are cons id ering using a nRF9151 on our upcoming project and we want to use the A-GPS functionality via your Nordic Cloud and transmit this via CoAP. However some questions...
Is it possible to get to port of an UDP socket (ephemeral, offloaded to modem) with NCS 2.9.0 and mfw 2.0.2?
I tried "getsockname" and get "errno 95 (Operation not supported...
Dear Nordic Team,
I am participating in the Board Designer Competition sponsored by Nordic Semiconductor and Autodesk Fusion 360. My project has been selected for free hardware...
Hi,
I am trying to build a BLE PAwR network jammer for wireless network hardening. I have three nrf52840 transmitting on channels 37,38 and 39, which blocks nodes from joining...
I'd like to update a firmware which is essentially made of 2 parts, say 0x1000-0x8000 is a "read-only" part and 0x8000-0x50000 is a "read-write" part. If I flash this firmware...
Hi Nordic Team,
Is there any way to input 3 audio streams (through I2S ) on nRF5340DK board are there any extra I2S Port available to input one more sinusoidal signal and...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
I want...
