Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Working with the NUS, I sometimes see ble_conn_params_on_ble_evt getting called in a way that will cause the data being passed through NUS to stop. Not all the time, just...
Thats the problem.
On Windows7, 64 bit, with the Bluetooth Stack from the USB BLE-Stick happens the following:
Windows (master) initiates the connection, sends a security...
Hi, I'm using nrf51822 and using SDK12.3 ble_app_uart.
My purpose is sending data using BLE module like this:
Custom Board -> BLE Module -> Android Phone.
It works...
Hi,
I am using 2 nrf51822 devices. one is central and other one is peripheral. I am using s130 softdevice.
When i was trying to connect NRF51822 to other nrf51822.
i tried...
Hello All,
I am working on nrf52840 trying DFU OTA by following steps provided in this link github.com/.../ota-prog.md . where they have mentioned to install python all...
Hi Nordic,
I've used a GPIO of the NRF52832 to drive a FET circuit which latches off the battery, however as the board voltage collapses I see a short pulse on the GPIO...
In single bank mode, need upgrade bootloader by DFU. Performing below procedure, APK shows "transfer complete". Application on target device is disappeared, but bootloader...
Why does the nrf connect app on Android need my location services enabled for it to work? I believe that is the case for most (or all) of the nrf apps in Android.
Hello,
I am using nRF SDK 12.2.0 , with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c to develop a driver for LIS2DE12.
...
I've read as many posts regarding changing the ble connection interval as I can find but so far have been unsuccessful changing the ble connection interval.
Below has been...
Hi all,
Does in any chip with some constellation (different SD) the device allows less than 7.5ms for the connection interval? Or is this value the absolute minimum?
I am trying to connect to a peripheral device advertising f0000000-0114-4000-B000-000000000000 as the UUID. The peripheral adds it to the stack via sd_ble_uuid_vs_add after...
Hi,
I am using ESB in one of our current projects. I have two devices: one PTX (master) and one PRX (slave). The slave may want to send some data to the master from time...
We have an nRF52832 and an MSP430 on a custom board. We would like to program both the devices using SWD interface.
Would it be possible that both these devices can share...
Hi,
I have an nrf51822 ( variant AB) and I am trying to program a simple ble app beacon example on it.
But I am failing over and over. After searching , I found out that...
