Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am using the eclipse/gcc toolchain as explained in this tutorial . I am able to generate and flash my application code and softdevice separately using hex format.
I am...
Hi, I programmed my nrf51dk with ble_app_beacon and I see a blink every two seconds on the board's led. I started the nrf Beacon app in my iphone 6. I first added a beacon...
I have two questions:
Question 1 :
What is the timer timeout limit on nRF51822?
The reason I ask is that I want to update the advertising packet periodically. Below...
Hi,
Here is the issue details.
I have my application loaded on the nRF51822 controller and it acts as a peripheral. The IOS device acts as a central.
The connection...
I am new to chip testing and need some advice on how to start. I am trying to test a nRF51822 on a custom PCB. The main elements of the PCB are the nRF51, a GPS module, and...
Hello,
I try to perform an pstorage store action after I'm done advertising just beform the devices goes in system OFF mode. Pstorage works fine before I start advertising...
I've gotten two PCA10001 boards working with the LED_mesh sample.
I cannot get the third board to run BLE_Gateway (it does not react to button presses, nor is it discoverable...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Dear all,
I'm not able yet to start advertising with whitelist whith this code:
void AdvInit(void)
{
ble_advdata_t advdata;
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED;...
I have a nRF51 DK board and its flashed with the SD 110
I want to have a timer which will interrupt every 50us.
This is how I set up the timer:
#define APP_TIMER_PRESCALER...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
