Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Im stuck that i can't get my Motherboards to update. Just goes into an endless loop of saying toggle power to rest it, starting boo loader, Couldn't start.. etc etc..
Attached...
I have a nRF51822 device which has softdevice and bootloader.
And I'm trying upload my app with following steps:
make .bin file with gcc
Push the DFU button, and...
I'm running a custom nrf8001 board and the nrf8001 is consuming approx 6.2mA on it's own in advertisement mode using the uart demo. Has anyone had this same problem? Any advice...
Flash write and erase works fine, if ble is not initialized( ble_stack_init()).
Once ble is initialized, any write to NRF_NVMC->CONFIG hangs the system.
Do I need to...
Hello!
We are using a custom hardware design based on nRF51822. Recently we switched to the new chip version QFAAG0 with softdevice 6.0.0.
Our application needs a repeating...
I have tried HTS(Health Thremometer Service) sample Program on nRF6310, PCA10006, SEGGER J-Link Lite and iPhone5C.
First time, temperature is displayed on the iPhone5C...
Hi,
I have a custom board with nRF51822 chip on it and tried to run the proximity sample program on it. I have used the nRF51822 develpment board + nRFgo Motherboard to...
www.dropbox.com/.../Screenshot 2014-04-03 11.41.25.png
I guess has nothing to do with crc16?
the call stall seems unreasonable, is it because my stack is messup?
...
Hi,
Is it possible to control the drive current of the gpio pin?
Can anyone explain the different possible drive configuration for gpio's (S0S1,H0S1, etc..)?
Regards...
I'm trying to compile the bootloader for gcc from this post: devzone.nordicsemi.com/.../nrf51822-over-the-air-bootloader-with-gcc
The bootloader start (I can find my device...
Hi,
I'm confused with the functions (sd_power_mode_set and sd_app_event_wait).
1.I think there are described with the same function.I can't tell the difference between...
Hi,
I've developed an application and tested it on the evaluation kit. Now i'm trying to run it on a custom board with a nrf51822 chip on it. I've made modifications to...
Hi,
I use to the nrf51422 with nordic's dev/ev kit.I want to build a project and the purpose is to get the sensor's date and use the ant protocol to deliver the date to...
