Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi all,
We are looking to use the nRF9151 and we are trying to determine estimated certification costs for US deployment
So, if anyone can help or knows:
What pre...
Hi,
I recently bought a J-Link Mini EDU and a Tag-Connect TC2050-IDC cable (bought the legged version for some reason, but I guess I can break the legs). I wanted to use...
i just rebuilt the code in the beacon_advertiser.zip file attach to this issue for the NRF52232....
the code runs as expected, though consumes about 200uA when sleeping...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
Hi, I previously wrote about an unexpected behaviour which I've made a diagram for below. It's relatively simple though, the COMP watches a voltage and fires a toggle event...
I am using NCS v2.9.1 and trying to enable a bootloader chain with NSIB and MCUboot. The regular setup works fine, however if I try to enable the minimal configuration, I...
Hello,
i have one PPK2. Recently i find the current reading from PPK2 is relatively large compared with actual current value.
For example, actual current value vs PPK2...
I've been using the ppk2 power profiler with version 4.0.1 for over 2 years and it has worked very well in providing a power source and monitoring/ with reviewing the power...
Hello,
We’re testing the nRF9160 GNSS performance on our custom PCB and have noticed that, even with A-GPS, the first fix after powering on the device takes significantly...
Hi,
I am currently evaluating the new nRF54L15 DK development kit.
I installed VS Code v1.96.4 with nRF Connect for VS Code Extension Pack v 2024.9.5 . I am currently...
Hi there.
I am trying to implement a 16-bit, 32kHz, 2 channel i2s interface which is being fed by a FIFO (the final source of this FIFO will be a DAB/FM radio module but...
Hi all,
I'm doing some tests with the nRF5340 DK to log with a custom timestamp source. I took the logging exercise 2 example and verified that the log messages are correctly...
Dear Nordic Engineer,
Hello!
We are currently in the mass production of our products. The chip model we are using is nRF52805, and the SDK version is nRF5_SDK_15.3...
We are using SDK 2.4.0 and have enabled MCUBoot to support OTA updates using the dual slot method. I have reviewed many posts and existing tickets and have not been able to...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
