Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am trying to get this example program https://github.com/ARMmbed/mbedtls/blob/mbedtls-2.11.0/programs/x509/cert_req.c (stripped out all the file handling stuff) to run on...
Hello,
I crated a custom peripheral for my application, I took the code from the Blinky example and i changed the service.
I set the FIRST_CONN_PARAMS_UPDATE_DELAY parameter...
I would like to be able to use 3 different USB descriptors.
1. CDC ACM
2. Mass Storage
3. Composite device with CDC ACM and Mass Storage
These should be selectable...
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK. I am using openthread protocol...
Step 5 of the Matter instructions at developer.nordicsemi.com/.../python_chip_controller_building.html
Shows getting the discriminator data. What is shown looks like the...
Dear Nordic Experts, A few short questions about mesh advertising in regard to Softdevice s132, 7.3.0, Mesh SDK 5.0.0 and nRF5 SDK 17.0.2:
How do you change the advertised...
Hello,
I'm running asset_tracker_v2 from v1.9.1 on a LTE-M network that does not give the time (UTC clock) info.
When no time information is given, the application should...
Hello
I have some questions about flash_fstorage example.
After reading the macro, it seems that fstorage will be located in .fs_data flash zone.
start_addr is set...
Hi,
Softdevice - 112
sdk 17.1.0
I am trying to evaluate the memory of the device. I am using nRF52810 and the datasheet says 192KB flash and 24KB of RAM available. ...
Hi I am using Unity test framework for generating unit test report and i also want to generate the code coverage report of the code for that i need how many lines of code...
Hey
I'm currently writing a thesis on IIoT and implementation in remote areas. We're trying to setup the nRF9160DK as EON device with all implementations on the board...
Hello,
I am experiencing trouble with NRF9160 chips that get stuck after typically 1 to 2 days of operation. This happens on all 6 boards that I have available. I'll describe...
Hi,
I am coming across an issue with app_scheduler and FDS.
While waiting for an event in FDS to complete (write, read, init, gc, etc) I go into a while loop calling app_sched_execute...
Hi,
What is the lifespan of nRF52810, operating at room temperature ? How long can it reliably work? Do you have some figures on this ? If yes, is it same for other nordic...
