Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
my project is freertos+nrf52832 based the templete in SDK; A sensor pin is connect to P0.17, and I configure it low to high level trigger interrupt.In the handler I will call...
Hi all,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK. I want to observe packages sent by the client and packages arriving at the server...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
Question:
I am testing SERCOMM module and nRF9160-DK, but there is difference in registration procedure .
When...
Hello, I migrated codes that I believed to be relevant to the UART output to a new project, namely the uart_init function and others, and it worked in main.c, which is where...
I am trying to use the connectivity firmware with an NRF52840 dongle to communicate with an nRF52840-dk through the nordic UART service, but I am unable to use the pc_ble_py...
Hello,
I am curently working on project with a nrf9160. I will use the nrf9160 as modem controled by a nrf52840 and command AT. I will send data true GSM every 12 hours...
Hi, This is the second time posting this issue. Using nRF9160 dk with nRF Connect SDK v1.3.1 with zepyhr v2.3.0-rc1-ncs2. I tried the BME280 sample from zephyr which gives...
Hi,
I connect the nRF52820 and other devices with UART and communicate with the baud rate of 38400bps.
I know that the transfer error rate is different for each baud...
I have two tasks and I want to run those tasks one after the other.
currently when I comment on one of the task, the firmware running without any error.
if run those two...
I have been unsuccessful attempting to perform an FDS write or update WITHIN the DFU Event handler... the update or write never completes (no FDS_EVT_WRITE or FDS_EVT_UPDATE...
Hi,
I am using NRF5340DK, and I want to define P0.20 as my SPI MOSI pin.
However, this pin is pre-defined by Zephyr as uart0 tx pin, in zephyr.dts:
Everytime I reset...
Hello,
Our product has two pieces of information that must be programmed during production: a shared secret key (128 bits) and a public, unique device identifier, also 128...
Hi guys:
I flashed the ble_app_uart(SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart.),
When I pressed button1, there...
Dear all,
I'm trying to modify ble_central_uart (SDK16) to connect two peripherals. I've achieved the connection and been able to print receiving data via UART.
But...
