Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
On a nRF52840 based coordinator, I want to support Zigbee 3.0 install codes and legacy devices with HA predefined link key at the same time.
1. Is that possible by...
I am working on a device driver for the W25Q128JV flash device. This is the first SPI device I've used with the nRF52840. I had some observations and questions about SPI programming...
Hi - I've bought two nRF5340 DK kits for some development work - and after about a week's effort and searching Nordic Semi documentation, Youtube and the internet in general...
I develop my own device on nRF52840 which will be HID device. And I have made my own HID descriptor of device:
And if I send data with function from example:
...
Hi,
As an alternative to writing a configration software for my device (a native app for windows or maybe android) I,m considering putting physical controls on the device...
I've installed Zephyr RTOS and built blinky example for NRF5340-DK board. Then, when I tried to flash output hex file into NRF5340, nrfjprog (using "west flash" command) gave...
I'm trying to debug firmware on our production device, but after programming the device a couple of times, I am unable to program.
Inside of Segger I see this log:
j...
Hi everyone,
In my company we are working with the last SDK release, and we build projects with make and gcc toolchain.
I have a quite wide request : since I'm using makefiles...
Hi all,
I have a custom nRF52840 board that transmits 32-byte packets to mobile device and I want to achieve maximum transfer speed.
The code is based on the ble_app_uart...
Dear all
The issue is:
heartRate and battery levels set by "bt_gatt_notify" in peripheral hr sample on nRFConnect v1.5.0 are not shown in iphone app of "nRF toolbox" ...
Hi All,
I am using the nRF52840, with SDK140 v15.0. I have configured the nRF52840 to be a SPI slave to a NXP processor. When I connect the logic analyzer I see signals...
Hello,
I am trying to build on the nrf5340_cpuappns sample, however this snippet seems to always warn unable to allocated UART send data buffer. Is there any reason k_malloc...
Hi Everyone!
nrf_serial.c and nrf_serial.h are gone in SDK 17.0.2. There are present in 16.0.0. I do not see any mention of this in the release notes.
Was this module...
i am using example code ble_uart for controlling gpio(led & buzzer) by editing bluetooth data handler. I am driving a buzzer using pwm.
led working fine i.e turned on/off...
