Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello! I use a 32kHz quartz resonator and I want to interrupt the program after 1 second with a watchdog timer. But when writing to it, 128 I get not 1 but 1.25 seconds. What...
Hello,
I followed the getting started guide but the kit can't connect. I'm getting this error:
net_if.net_if_init: There is no network interface to work with!
Is this...
Hi there,
I have a question NRF52840_PCA10056 and its SDK is latest nRF5 SDK.
The scenario is below:
The NRF52840_PCA10056 build a connection with a smartphone like...
1. It is understood that zigbee3.0 certification requires Green Power, but I did not see the definition and use of Green Power in the example. How does the nordic zigbee pass...
Hello Everyone,
I am trying to compile zigbee_light_coordinator example. I have my path included as ../../../../../../../external/nRF-IEEE-802.15.4-radio-driver/src in make...
Hello,
I have accidential removed the DFU bootloader on my PCA10059 dongel..... is there an image that I can write to the dongle to get it back into its out of the box condition...
Hi there, I have set my SAADC to have an acquisition time of 3us , however when I toggle a pin before and after calling
nrfx_saadc_sample_convert
I measure the time of...
The sample project is "nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\experimental\ble_nfc_pairing_reference"
I think "micro_ecc" is a normal build.
Please check attached...
Hi,
Using the Secure DFU from SDK 14.2 I managed to integrate the NUS peripheral example to have access to an UART pipe in parallel to the DFU when running the boot loader...
Hi,
I am interested in testing the capability of Bluetooth 5's long range.
I have two nRF52840 dongles (pca10059 v1.0.0). So far I have had one dongle using nRF Connect...
Hi
In the example Nordic UART BLE_central, I notice that when I send data over UART to the central device, it echoes the data sent and I see it as an output in the central...
Hello,
I'm having an issue about the FDS. Indeed, i want to update some structures already saved in flash so i call the following function : fds_record_update. I can see...
I am trying OTA DFU on nrf52840 over BLE using segger. Is there any example code with proper libraries? Because I'm getting an error message: ant_error.h: No such file or...
Hello All,
I am having trouble changing the 'ble_app_multiperipheral_pca1056_s140' example to work with long range. I have read a few of the blog posts and similar devzone...
Hi all,
I am working on a project where the requirement is a sensor collecting data and sending to the NRF52832 via UART. Every 40ms, the NRF52832 will receive 40 bytes...
