Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
In migrating a project from SDK 14.2.0 to SDK 15.3.0, I'm also trying to move from the "legacy" non Easy DMA SPI driver to the Easy DMA one. I don't much care whether I use...
Hi,
I've been struggling with a problem with my builds for over a year now.
On some builds NFC works perfectly, but on many it doesn't - and I have no idea why. I can...
Hi, I'm having problems with proper softdevice reinitialization. What I'm trying to do is work out proper reinit solution - what I'm doing is enabling BLE_stack and all the...
I want to store a few parameters in flash. I don't want to use an external EEPROM because it takes an additional space on a board.
Does anyone know how to do it or a sample...
Hi,
nRFConnect is behaving differently for apps on different SDK versions. I am able to do a DFU via script something similar to the one here https://thegecko.github.io...
After much work I can build the nRF9160 at_client sample project and flash it into the development kit. Using nRF Connect, the at_client sample project only prints the line...
Hi There,
I have developed an initial application on SDK11, based on the UART example, with Keil and it worked perfectly with the nice low power that you guys are capable...
Hi,
I have created a project with nRF52840 DK that reads sensors data and transmits them with BLE UART to my smartphone. Everything works fine.
Then, I tried to do the...
i am working on mesh application using two nrf51822 and one nrf2832. I started from light-switch examples. nrf51 set as two server and nrf52 as a client . In server side integrated...
Hi all,
in the datasheet of the nRF9160 is mentioned, that the same antenna can be used for LTE and GPS.
Page 364, chapter 8: GPS "Dedicated GPS antenna or shared antenna...
I'm using nRF52840 with SDK15.0.0
Following this tutorial : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-characteristics-a-beginners-tutorial...
hi,
I'm trying to add a new BLE service to my device. I've followed the instructions in tutorial : devzone.nordicsemi.com/.../ble-services-a-beginners-tutorial , up to step...
Hello,
I have just started working with mesh and I'm using the 0.9.2 Mesh SDK. When I use the Serial interface (nrf_mesh_serial) I don't see any function about rx or rx...
Hi,
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh SDK 3.1.0 and nRF5_SDK_15.2.0.
the data...
