Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi Developers,
I am exploring the light switch examples, client, server and provisioner, every time a node is provisioned it uses a unicast address, what if I want to use...
Hi all,
In our project we are using nrf52810, SDK 15.0.0 and ble_app_uart.c example.
We are using our custom board in which MCU is communicating with BLE through wired...
Hello,
So i found this code from one of the earlier post which combines the saadc example with ble_app_uart example to make analog values from the analog pins to be sent...
Hello,
I want to use multiple timer interrupts, want to fetch values from 3 analog pins on every 20secs and then average three collected values at every 60 sec. so i would...
Hi currently I am handling a project in which I used nRF51822. I am using SDK 11 and softdevice SD130. I want to know is there any significant difference in power consumption...
How do I rename the Solution/Project from template_pca10040 to insert_name ?
I copy-pasted the template_project folder and renamed it
I changed the names in [SDK]\[SDK...
I have a nrf52 DK that I want to use to program the nrf52832 IC. I have bought a qfn48 adapter from here . I wish to use this adapter to place the IC then make connections...
Hi, all. I am in need of serious help. I need to set up a wireless mesh network using the nRF52840 SoC. It must have 9 nodes and be capable of multi-hopping. I need to set...
After configuring and enabling COMP, when READY event emits, is the RESULT register valid? Rephrasing the question: must you trigger the SAMPLE task to ensure RESULT register...
Hi, I've rebuilt so far with the help of multilink examples, the uart example that I can connect to two devices (According to the status of connection-led and the debug info...
SDK:15.2 KeilC:525 SoftDevices:s140_nrf52_6.1.0_softdevice Hardware revisions: PCA10056
I have try the multiperipheral in 4 smart phone connection in blinky App. But I need...
Using nrf52832, SDK12.30 demo project ble_app_uart, testing with nRFconnect app.
Load ble_app_uart demo to board and run. Open nRFconnect on smartphone scan, and connect...
Hello,
I am encountering a small problem with my timer, I followed the tutorial : devzone.nordicsemi.com/.../application-timer-tutorial
The purpose of my project is to...
We have been using SDKv11.0.0 with S130 softdevice on nRF51822-QFAA rev 2 on a custom board with no problems at all.
Since our nRF51822 BLE module vendor no longer support...
Hi guys,
I flashed the mbr hex file and then the open bootloader to a custom nrf52840 board. When i first connect it, it boots into the bootloader mode and i am able to...
