We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi all. I would like to get the current RTC tick when there is an advertisement RX event on multi-link central. I am going to store the advertisements along with a time i...
Hello, In one of my codes, I use the printf function. It works properly when implemented in the int main(void), but when I try to use it in a static void NAME (void){} function...
Hello,
I'm checking the DTM code from nRF5 SDK15.2.0.
In the ble_dtm.c file, line 763:
And in the ble_dtm.h file lines 104-110:
DTM_PKT_0XFF and DTM_PKT_VENDORSPECIFIC...
Hi.
We got Thingy for power measurement purposes. I tried first the it out of box and it works fine. Same with pre-built image.
However if I build the SDK example and...
non connectable advertise success when in SDK 8.0.0, however I got error code 0x00000007 when upgrade to SDK 9.0.0.
I find out error code 7 is NRF_ERROR_INVALID_PARAM,...
hi,
my development kit nrf52832 is not detecting via phone nrf connect app . it appears like no device found .i flashed the ble blinky example program (sdk 15.2version)...
Hi to everyone!
I recently bought the nRF52 SDK to use it in a project, but the kit contains a NFC antenna and I don´t know its use.
My project its about Bluetooth Mesh...
i use the sdk15.2.0, the chip is nrf52832,my device have both BLE peripheral,and BLE center in my application, I use center to connect with peripheral, i directly use the...
HelloI am trying to program nRF52832 QFAA and am succeeding only partially: the debugger is connecting to the chip, and I can RUN step by step, however, I'm seeing only the...
Hello, I have adjusted the Uart Central Example from the SDK 15.1.0 with the stack s140 v6.1.0 so that the device can connect to two peripherals. The name of the device is...
Hi All,
I use SDK 15.2 to periodically trigger ADC acquisition tasks via PPI. But SOFTDEVICE: INVALID MEMORY ACCESS error occurred while the system is running.
I found...
I am using nrf52832, SDK v14.2, Softdevice s132_nrf52_5.0.0.
I had program the softdeive in flash, and I program the DTM firmware as application(start address set as 0x23000...
Hi Guys,
How do I configure Embedded Studio to generate full build log output? For example I want check whether all the header I included is compiled correctly.
Please refer back to the original link
The reason for this massive edit is because this post included code I tried to reconstruct from memory at home with only the SDK sources...
Dear team, We are getting an error in running the Android app in the background: ' Service destroyed '. It comes when the app is minimized and use any other app after that...