My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hallo,
Currently I'm investigating different Low Energy Bluetooth solutions for our healtcare products that we build in Televic Healthcare.
So here is the setup I...
Hi all,
I'm a little bit confused with the Thingy52 SDK.
The "ble_app_thingy_s132_pca20020" code is the same of the "thingy_v2.1.0.HW_1.0" precompiled hex file?
Thanks...
Hello
I would like to know GPIO leakage current, especially when the GPIO outputs Low
state, leakage current flow thorough the High side MOSFET parastic diode.
If nobody...
Hey everyone,
I have measured input current by different transmit powers:
nRF52840
Equipment: Konstanter ssp 240-40 as current source
Agilent 34401Afor current measurement...
I have a custom board on which I am running the fatfs example from SDK15.2.
On SD Card Initialisation the CMD0 response is unexpected: -
Where the NCR would be expected...
Hello-
We are preparing a product for Bluetooth certification. Our design has a PCB antenna and the the testing house is requiring an SMA RF coaxial cable to interface...
I have created a custom Board Support file for my custom Board But it is not able to advertise the BLE Device after I use My custom Board File. When I use Predefined board...
Hi,
We need to collect sensor data from nrf52832 and after some processing, we plot data and generate some notifications etc. on smartphone app.
Shortly we need to design...
Hello, I'm developing a solution by using MESH SDK : nrf5_SDK_for_Mesh_v2.1.1
There is an ASSERT on access.c in nrf5_SDK_for_Mesh_v2.1.1_src\mesh\access\src\ as below. ...
SoftDevice: S132_5.1.0
Environment: I have 1 Device Advertising and about 200 "tags" waking up every 10 seconds and scanning for those advertisements and connecting, I have...
HCI for NRF52840
Hello
I m using a STM32 + NRF52840 and i have a mbed project in my STM32 and i want to use The NRF52840 only as a Bluetooth component, is there an example...
Hi guys,
I compiled the openbootloader example and when I try to run it on NRF52840, It gives segmentation fault:
(gdb) load nrf52840_xxaa_debug.hex Loading section .sec1...
Hi,
I'm having problem with the example code in the "Bluetooth low energy Services, a beginner's tutorial", the code was downloaded from github.
I'm using SES V3.5 for...
Hi,
We are currently develop our costum board with an nRF52840 SoC. Are the nRF52840 shipped with an initial bootloader to programm the device via USB? Because if possible...
