Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Quick question: when will the nRF52840 DK available? On the nRF52840 DK page, there is a recommendation to avoid the PDK:
"The nRF52840 replaces the nRF52840 PDK which is...
I have the super typical problem of needing long data transfer greater than the 20 byte MTU size.
I have a basic protocol that has the total length of a long message coming...
Hello everyone, I am very new to nRF52832 Development Kit and was testing some examples to get familiar with this kit, however i encountered an issue while testing the ble_app_uart...
Hello,
We are having problems with Gazell pairing. Both the host and the device are using the Gazell stack from the nRFgo SDK 2.3.0.10040 ported to run on an Atmel SAMD20J18...
sdk 15.0, SES
In CMSIS checked NRFX_TWI_ENABLED, and checked and unchecked TWI_ENABLED to no avail.
Looked at driver API , but with no specific hint.
Looked for other...
Hi Engineers !
We are going to implement AES CRYPT/DECRYPT Protocol over BLE to add some additional protection against HACKing with use of HW " 6.6 CRYPTOCELL" the MODULE...
Hi, I want to use a couple of 0805 resistors, hook them up in tandem to 220V AC power source, and then do some zero-crossing detection.
I know I know, this totally isn't...
Is it possible to use the Segger SystemView software with the NRF52832? When attempting to use SystemView, I get an error "RTT Control Block not found". It's possible to enter...
Hi,
I can't find information what shape of spectrum I should expect from test mode (CONT_WAVE = 1, PLL_LOCK = 1). At the moment I get main spike with smaller symmetrical...
I'm running into an issue when trying to use the timeslot API for advertising while concurrently scanning. Scanning is using a 100 ms interval with 50 ms window and initialized...
Hi!
I have created a project for nRF52 DK in Segger Embedded Stuido. I wanted to creat it for nRF51 but there was no eamples to start from in the sdk that supports pca10030...
I used the example ble_app_cts(SDK12.3),but when I connected the board(NRF52832) ,I did not find the cst service,Now,I want to know why I did not find the service and where...
Hi everyone.
I'm currently working with NRF SDK for Mesh v2.0.1, SDK v15
I'm adding light switch provisioner to light switch client example.
In file provisoner_helper...
