after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi Support,
I am using
I have my own customized board with nrf52840 . i am using SDK v15.0.0 with Softdevice verison v6.0.0
I am advertising with DFU and NUS services...
Hello,
I used the uart example to print text over serial communication from the SDK v11.
The problem is when I write lot of text consecutively, I don't receive all data...
i use the BLE uart example to test. I delete the UART hardware init and just use the BLE send data to phone every 500ms. I found whatever i set the MIN_CONN_INTERVAL and MAX_CONN_INTERVAL...
Hi,
Some time ago I ask a question about changing the publish address of a node in the mesh locally. I received the answer in the following threat and verified it:
https...
Hi All,
I used the app "ble_app_uart" and "ble_app_uart_c" on two custom boards mounting a n52840 QIAACO.
I know that in the app (nRF5_SDK_15.1.0_a8c0c4d\examples\ble_peripheral...
Dear Sir/Madam,
I want to measure the data speed between two BLE 4.2 based devices and two BLE 5.0 based devices.
Using nRF52 products for this purpose.
Kindly help...
I know that the nRF52832 is strictly a 3.3V device however, I was wondering whether any of the GPIO pins are 5V tolerant?
Is there any internal clamping diodes within the...
Hello,
I have noticed, that https://github.com/NordicSemiconductor/nrfx was updated with a nfct driver. I am trying to extended the nrfx port on micropython (see https:...
Hi,
I'm trying to setup the Peer Manager on a nRF51822 with installed the S130. I'm working with Eclipse where I installed the 12.3.0 SDK.
At compilation time I get the...
Hi, I have a two part question, I know the NRF51822 (and I believe all 4.0 BLE chipsets) are being sunset, when will this start taking place?
Since I'm currently using the...
HI,
i am using nrf51422 with sdk13.3.0 and soft device 130
i am receiving 69 byte of data through UART, i am compressing data in two packets. here after transmitting a...
I have an issue with BLE on Android when using low duty-cycle directed advertising and I'm asking here hoping some people have already seen that issue or something similar...
Hi,
I'm working on a custom bootloader based on the one included with SDK 15.
I have a blocking method (i.e. while loop) that runs at the end of the transmission of all...
Hi,
Some general Nordic BLE device questions:
How to add Characteristic?
How to send data to given c haracteristic?
We are using SoftDevice 132 with Segger IDE.
...
