Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I have compiled and debugged the temperature_pca10036 code from nRF5_SDK_v11.0. I have used termite terminal for getting info about transferring of data from nRF52832 board...
Hi,
I am using nRF52 board and want to change the RESET output from P0.21 to P0.2.
-I have CONFIG_GPIO_AS_PINRESET defined in the makefile.
-When debugging I can...
First, we implemented ble secure dfu application on nrf51dk. After, we want to program nrf51822xxaa device with same ble secure dfu app. In addition, we saw about rom/ram...
Hello Friends,
I've Get my Thingy from Nordic Tech tour and have a good time with it.
I think everything is perfert, but location of ccs811 ( Tvoc +eCO2 Sensor ) is...
Hi Nordic & friends,
As I know, DLE(data length extension) is not supported in S112. We are using nrf52810 in our development, so I make a test.
A long data packet(>=20...
How can I perform multiple A / D conversion?
I created a program with reference to the method of the old version of A / D conversion, but the function name and argument used...
Noted that the new V15 SDK for IAR does not have linker config file set correctly on ble_app_blinky_pca10040e_s112 project. The .intvec start location was set to 0x19000 and...
Hi all ,
i'm using nRF51 DK ,im getting issue while program downloading on flash .Program compiled correctly(no any error) even it show flash downloaded but the application...
Hi There,
I have been looking into how to connec my QSPI NOR Flash to the NRF52840.
I have notivced a discrepancy between the comment in the Table 3. of the OPS and the...
Hi,
I have a peripheral which sends data to the central and from central i n eed data to be send to Mobile App
is it possibe to do and how???
or any other ideas you...
I am using Keil 5.24.2
I already downloaded and compiled with build_all the micro_ecc. Having no issues here.
According to the error, and what I read in another thread...
I have been investigating the possibility of using the QSPI external flash peripheral on our NRF chip. After doing a typical qspi read command, the external flash chip would...
Hi,
when i make a connection to my device i get 4 `BLE_GAP_EVT_CONN_PARAM_UPDATE`.
If i make an action of read or write when update event occures i get a duplicated read...
