Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi. Currently, i am testing the BLE power consumption on nrf52.I set connection interval 20ms(min=10,max=30) ,slave latency 0 and connection data size 20 bytes.in addition...
It seems like the IAR startup file in SDK 11 for nrf52 is older than the one that was included in the previous SDK 11 alpha
IAR Embedded workbench 7.50.3
I have a queston for softdevice S130 example about Environmental Sensing service.
I readed spec. but I can't find out any ESS profile example in SDK.
Is SoftDevice S130...
I want to use the nRF24LU1+ for a project where it will be a HID usb dongle. But I dont get which tools I need to make it. The KIT DEVELOPMENT NRF24LU1+ work for it?
T...
Hello,
This morning i did migration of my code from SDK 11 alpha 2 to 11 final on nRF52 and i have a big problem.
Nor bootloader or application do advertising. Am I...
I want to merge the softdevice and application in the makefile is it possible ?
if not possible what could be the easier way. I am using Linux OS .
thanks
Hi everyone.
I'm trying to program a NRF51822 Beacon using the nRF DK board. Of course I looked around here for advice on what type of connector to obtain.
devzone.nordicsemi...
Hi,
I have a hardware (wired) UART transmitting data to the nRF51 at intervals. I'm currently trying to implement UART-BLE that runs could concurrently with the wired UART...
is there a version of nrfutil that works on linux?
this one doesn't: github.com/.../pc-nrfutil
$ nrfutil dfu genpkg --application _build/nrf51822_xxac_s110.hex fota.zip...
Hello,
I have used ble_app_uart example and wants to transmit 12 bytes data over ble using this function ble_nus_string_send call.
In 1 second how many times ble_nus_string_send...
Hi,
At the moment I'm trying to make some current measurements with the new nrf52 dev-kit from the global tech tour. Unfortunately I'm not able to go into Idle- or even the...
Hi,currently i want to measure the current consumption of nrf52 DK. I followed the tutorial nRF51 current consumption guide ,and use the Power profiling application in the...
HI. currently, I have used the nrf52 board to test the power consumption of ble,I followed the tutorial nRF51 current consumption guide,loaded the Power profiling application...
