Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
when ntfx_spis_init() is done , NRFX_ERROR_INVALID_STATE errer occured.
pcb_state is NRF_DRV_STATE_INITIALIZED.
my code is
int cc3235_spi_init ( void )
{
...
Hello, Hardware : nRF5340DK SDK : v2.6.1 Context : Creating a prototype using a Load Cell and transmitting its weight on BLE. Disclaimer : I'm new to the settings subsystem...
Hello,
We are currently helping one of our client develop a product using the nRF5340.
DK versions:
nRF5340-DK
PCA10095
2.0.1
Host OS:
Ubuntu 22.04.2...
I'm a beginner to nRF52840 board, and I'm currently doing the nRF Connect SDK Fundamentals . But I failed to build the Blinky Sample due to the following error:
I'm sure...
I am working with the module nrf5340-DK. I am searching for an example to use the QSPI with the onboard external memory, could you share an example? and the other question...
Hi,
We are planning to move with the nRF5340 + nRF7002 for our upcoming project. We have some queries related to power section which are, 1. can we an use the same power...
This one is throwing me for a loop. We have a very basic NFC component in our firmware that serves up a static NDEF file and wakes the MCU from a system_off state.
We have...
Hello All,
I am programming an nrf52480 using zephyr on a windows machine.
I am trying to write a bluetooth peripheral characteristic, ore specifically to the led...
When using two nRF5340 Audio DKs as bis_transmitter and bis_receiver respectively for the iso_time_sync sample, the iso_recv event is triggered.
However, in the respective...
Hi,
I use nRF52805 chip for BLE tag. FACTOR_MODE pin will be used for production stage. At F/W start point, F/W reads FACTORY_MODE pin, if the pin is high, F/W will enter...
I am trying to program nrf5340 using this command: nrfjprog -f NRF53 --program merged_domains.hex --verify --recover -r
It works fine if readback protection is not enabled...
Everytime I make a call to the usb_dc_ep_write function I get error -22 meaning invalid argument. I have tried everything I can think of. I tried sending a blank packet with...
Hi：
My environment is: nRF5_SDK_17.1.0_ddde560, keil, s113_nrf52_7.2.0_softdevice When using the ble_app_uart example, "Failed receiving NUS message. Error 0x04. " appears...
After discovering that MBEDTLS requires at least 48000 bytes of heap to function, I've had to desperately find some spare bytes to conduct a TLS session over WiFi using a...
