Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
I am trying to get SPI working but the cs pins is on P0.02/NFC1.
I believe this is because the gpio is not configured correctly. Here is a screenshot of my device tree....
Hello,
My application runs perfectly for like 14-15 hours and then when trying to connect to go into RRC connected mode to transmit the modem crashes with following error...
Hello,
we noticed for one of our boards that the nRF9160 is not able to startup with a floating MISO pin on the SPI where the flash is configured in device tree (SPI1 /...
We have a custom board based on the nRF52805 that does not have a LFXO, instead relying on the RC. We are using NCS 2.6.1.
We see current spikes every 4 and 8 seconds that...
Hi,
as mentioned in the title, when using the official vscode extension (nRF Connect for VS Code) for debugging and stopping a debug session, the target state does not get...
Hi：
I have the following hardware structure：
FPGA < -- SPI -- > NRF5340 (TX) -- ! ( ESB ) ! -- NRF5340 (RX) < -- USB -- > PC
Due to the nature of my application, I need...
Hello!
I am trying to collect data from an nRF52832 device which works as a peripheral to another device nRF52832 which operates as both Central and Peripheral.
Description...
Hi,
I am downloading GPS Almanacs from U.S. Coast Guard Navigation Center web site to inject into the modem using nrf_modem_gnss_agps_write() . Below is current almanac...
Hello,
I need a way to decide on which Api to use for UARTE (configured as uart1) once in main(). I am not intending to switch between them nor to use them at the same...
I am currently working on a project to migrate to the nRF Connect SDK. We are using the NRF52840-CKAA-R7 package of the nRF52840. However, I have not been able to locate the...
I'm develping application on nrf52832 with nrf5SDK v17.0.
The connection interval is set to 12 to 16.And the conn_sup_timeout is set to 1000.
The condition happened frequently...
As I understand it, any applications using the modem libraries on the nRF9160 must be built in the non-secure domain. The MCUboot and TF-M needs to be in the secure domain...
Hi.
I need read the external voltage in input P030, and the battery backup voltage in P031.
If I read using only one channel, the P030 (AIN6 ) the value that show...
I want to send key strokes between two pic 16f887 microprocessors using the nRF24L01. I assume I can use ShockBurst to do the job. The master sends the key strokes and the...
Hello,
In the nrf5340_aduio application. I found it support 2 channels both of output(mic signal) and input(audio signal) on the USB device.
But i want to know if it can...
