Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Dear Nordic Team,
on my board with NRF85240 High Voltage mode is used. Accordingly to datasheet (5.3.8.2 Regulator Specifications, REG0 stage), in this mode the following...
Can you help with why I get this serial debug message when trying to start Headset nrf5340_Audio DK in DFU mode
HR [00:00:02.068,450] <err> dfu: SMP_SVR Advertising failed...
Hi!
I have an issue with control of the MAGPIO during RFTEST procedures.
The device is using RF Switch (like Thingy91) and I want to perform SNR/Received signal power...
Hello All,
Hoping to hear your opinion as I have little experience on how reliably the following would work.
The device should count pulses or edges from a reed switch...
Hi,
I'm using a Thingy:53 for some prototyping work. The device is configured with the standard USB CDC ACM as logging backend and I use pyserial-miniterm to access the...
Hello All,
I hope all is well. I have now been using Nordic ICs for close to 10 years and have become familiar with SDK5 and developed multiple applications using it....
Hello,
I would like to fast adc some analog signal from my opamp PCB. I am using nrf5340DK SDK1.9.1 with VS Code.
Got the example code nrfx_saadc.zip from and my first...
Hi,
I'm using the following function in my project, in order to get an idea of how much memory can be reserved with malloc :
This function should return the last value...
Hello,
I have a question about the Kconfig extension for VSCode.
When I use the nrf52840 DK, the Board Selection correctly check the nrf52840dk_nrf52840 and all the configs...
I've been continuing to work on why my power level seemed low after getting the Skyworks FEM in my Fanstel BT840x module going, per this thread:
So far, I've been setting...
I want to increase the rate of data from UARTE to RF FIFO.Can data be transferred from the cache to the RF FIFO using DMA?
nrf52832 nRF5_SDK_17.1.0_ddde560 S132
Hello, I am trying to understand the adc example using the PCA10056.
HI can see the following code that initializes 3 `zephyr_user` channels
In the DT file,...
Hi,
I recently went through the manual installation instructions for the nRF Connect SDK posted here ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing...
Dear,
I would like to remove the DCDC converter in between the li-ion cell which is supplying the system and the system.
The idea is to use our micro battery as the...
