Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
I use whitelist to store bonding information. Is there an upper limit to the number that can be stored...
Hi,
I am trying to configure a GPIO pin P0.21(as this is exposed pin on Thingy:91) from nRF9160 on Thingy:91.
I am using nRF Connect SDK 1.4.1 with Nordic version of SES...
Hi,
I am evaluating the LTE modem demo. I downloaded the demo binary firmware images a few weeks ago. Today I installed the LTE Modem demo into my dev kit. It connected...
I want to develop a 2.4G mouse Dongle and have used NRF52840 and SDK 17.0.2. When I have used USB or ESB one by one - all is Ok. But when they are used together - usb driver...
Hey all
I've been searching and trying all sorts of options for this but I'm stuck.
I'm currently working on a Thread sensor prototype on the 52840DK. I'm trying to...
There are two issues in one here. The easy fix is the check for overflow in format_offset_string_print() if (length <= p_cli->p_ctx->vt100_ctx.cons.terminal_wid - terminal_offset...
I have a bit of an odd one, and would appreciate any input. We have a fairly complex project, which does various things, but some of the time, I get a hardfault. The issue...
I am getting linker errors such as the following:
Output/Release/Obj/saadc_pca10056/nrf_sdh.o:SDK\components\softdevice\common/nrf_sdh.c:83: undefined reference to `start_sdh_req_observers...
Hello i have a keyboard with nrf52840 with ZMK firmware, BLE, adc, gpios, i2c0, usbd, DCDC and CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC
When it is connected with the computer...
I would like to know the natural interrupt priority among different peripherals of nrf52840.
Specifically I am looking for default interrupt priority between RTC1 and TIMER1...
Hello, guys. I'm using the PCA10040 and the SDK 16.0's BLE UART peripheral example. I am trying to make PWM signal below.
When PWM0 stops, PWM2 works, and when PWM2 stops...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr. In this process I am currently trying to extend the BLE MTU size beyond the default 23 bytes...
Hello,
My device is a USB HID peripheral connected to a PC. There is a case when the PC is turned off, but USB power is present. I want to detect this situation.
At the...
Is it possible to detect the presence of a Low Frequency Crystal and configure softdevice to use if present, otherwise use the internal RC oscillator?
A proposal would be...
