Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hello,
I would like to use Nordic SDK libraries (currently I'm using SDK 17.0.2) to read and write on a FM24CL16B I2C F-RAM.
This device has the following writing workflow...
Hello,
I recently used GPIOTE Events to manage Digital state changes and this is awesome. I would like to perform similar thing but when a PIN goes under/above a given voltage...
Hello,
I'm running NUS sample from NCS SDK 1.5.0 on two nRF52840 PCBs. Central board is Taiyo Yuden module and peripheral is nRF52840-DK. I've added some lines to prj.conf...
I am looking for an example where I can enable UARTE0 and UARTE1 on the nRF52833 DK. I am using nRF5_SDK_17.0.2 with Keil uVision V5. I am successful with the loopback example...
Hi,
I'm new to building circuits with Nordic devices and am unsure about how to connect the MC3672 accelerometer: https://mcubemems.com/wp-content/uploads/2020/03/EV3672AB...
Hello,
We have been working on Nordic nRF52-DK board.
Board can be reachable by Bluetooth in the first 10 minutes of power supply. However after 10 minutes, we can...
Hi everyone ! I am working at a project. I dont't know which mcu was used this project but it was written for pca10040 and used s132. Many values are write to flash memory...
I merged in some of my code to the examples/thread/dfu/client in the v4.1.0 SDK for Thread and Zigbee. After getting OTA DFU working, I moved onto some commissioning related...
Hi there,
i'm wondering if it's possible to get access from the demodulator directly within the nRF52? it shows in the block diagram below, is there any way to bypass...
Hello Nordic,
I'm trying to run nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart (PCA10056, S140 softdevice) with default sdk_config.h . The master is nRF Connect...
Hi,
I am new to nRF Connect SDK. I am trying to achieve over the air Firmware upgrade through nRF5340. The SDK i am using is nRF Connect SDK v1.5.0 .
As per my understanding...
I am currently going through the usbd_ble_uart example and understanding what states make which LED's active,
Within the example, LED_BLE_NUS_CONN is defined as BSP_BOARD_LED_0...
How to use the internal 32.768k crystal oscillator for nrf5340？
NCS: V1.5.0
example: ncs1.5.0\v1.5.0\nrf\samples\peripheral\radio_test
Only HF no LF config.
Hi all,
I'm trying to use one of the built in sha256 libraries. As I've enabled the CONFIG_NRF_CC3XX_PLATFORM and CONFIG_NORDIC_SECURITY_BACKEND I thought I would pick this...
