Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
We're using nrfutil v.6.1.0 in order to perform DFU updates to our target board using nrf52840-Dongle, and we're experiencing some issues. Everytime we try a download, even...
Hi! I am using an nRF51 DK board and the app_pwm library. I am using SDK 12.3.0.
Why doesn't
stop the PWM? I call it right after initialization:
... as well...
First of all, I ask for your understanding of my poor English. I am a student studying in Korea. Ask for help.
I wonder how each pair recognizes each other when two pairs...
Hi,
I am just staring my evaluation with nRF9160-DK. The video says I need to turn the dev board on, insert SIM card and wait for LED3 and LED4 to light before proceeding...
Hello,
My firmware is based on the ble_peripheral_HID_mouse (nrf52 DK, pca10040e_s112). I receive unexpected BLE_GATTC_EVT_HVX events of indication type from Client side...
Hello, I am using nrf52840 dongle for development purpose whether there is any provision to generate the code which is used by nrf connect for desktop from the app or by any...
Hello, everyone.
I'm dealing with an example of a sensor in SDK v14. I've checked it's working and now I'm going to put it in the code I made in SDK v17.
Code must be...
What happened to SDK 7.0.0
It is no longer available for download.
I assume some problem was discovered, so it should not be used any longer, at all?
Any help a...
Hello,
For clarification I use the nrf5_SDK_for_Mesh_v2.1.1. and the nrf52832.
I'm trying to scan for Ibeacons in which I need to get the UUID, major, minor, and the device...
Hello,
I have intention to use NRF52840 as HW peripheral just for communications over BLE. It means, it will be connected to the main MCU and provide interface for utilizing...
I am using nRF52840 Dev kit (PCA10056) , with nRF Mesh SDK 4.0 and nRF SDK 16.0 .
I have such FOUR kits . I have been able to modify vendor model for a sensor to transfer...
Hello everyone.
I'm a fresher of programming nRF52833. I'm doing an application for my final project in my university. What I need is get the RSSI in order to analyse the...
Hello -
I am evaluating nRF52840 to replace the Bluegiga BLED112 in an older product. I am surprised to get very low range from the nRF52850 USB dongle, barely 10-15 feet...
Hi, NordicTeam
Nrf52805 as slave and mobile phone as master to connect slave. NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, MTU = 23, the master sends the Prepare Write Request to...
Hi,
I'm developping a new application where the device normally is in low power (waiting button with an interrupt)
while(!gIsButtonSwitched) { __WFE(); }
the consumption...
