My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hello,
i follow this example " https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic-DFU-to-a-SDK-Example " to change ble_uart_example (enter new library...
Hello,
With the last environnement version, there is a potential issue
CMake Error at F:/Git/YYY/Projects/ZZZ/TTT/nRF_SDK/ncs/zephyr/cmake/extensions.cmake:395 (file...
Hi, I have built an nRF52832 application using SDK15.3 / S132 6.1.1 that runs on E0 chip revision (development board). If I program B0 chips (production boards) with it, it...
Hello, I encountered a problem during my development. My phone is paired with MITM and pin code security. I enabled the service changed indication to indicate the smartphone...
SDK ver：15.2.0
demo：usbd
i want to use the 52840 usb function ，the pc is the host ，the 52840 is device。
i cant use respond_setup_data to send data to pc。
but how to...
Hi All,
I am using nRF52840 for product development , there is a issue on measure the TX power .
Now , my firmware is development with softdevie, I want to comfirm my...
I am a newbie to Nordic thingy and Keil. So please help me with this.
I downloaded SDK and opened it in Keil. It asked for updating software packs update and it was
done...
Hello expert,
I follow the steps with this tutoriel " https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic-DFU-to-a-SDK-Example ".
I reach to the DFU...
Hi
I made a custom board. (using nrRF52832)
At frist, I tested my code on 52DK(PCCA10040). It is worked.
And then I tested my code on custom board. I changed my code...
Hello,
Sorry for simple question. (Yup, I'm Canadian and we say sorry a lot!) I have SES 4.18 and nRF5 SDK 15.3.0 installed on my Mac (10.13.6) and cannot get logging (NRF_LOG_INFO...
Hi! I am using the MQTT simple sample that i have modified to continuously send data after receiving a message. I also have connected a MS5837 pressure sensor to the nRF9160...
I'm trying to get DFU OTA working with SDK 14.2.0, SD 132, on the nRF52832. I'm using the bonded implementation. My DFU event handler is getting passed
BLE_DFU_EVT_BOOTLOADER_ENTER_FAILED...
So I want to run the nRF52811 chip so I removed the nRF52832 chip from its development kit and soldered the nRF52811 chip but I cannot seem to program it. What are the required...
Hi,
I am using ncs 1.0.0 and modem fw version 1.0.1.
I am using PSM mode in my firmware.
I want to toggle state of one gpio when modem goes in active or inactive state...
