Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I'm using SDK 15.3, nRF52840, with the ext-flash read/write QSPI demo project.
block_dev_qspi_init(), in nrf_block_dev_qspi.c, does not uninitialize the QSPI (by calling...
Hi,
I am trying to install nRFgo Studio version 1.21.2 in my Windows 7 (64 bit OS), but half way through, installation is rolling back the installation changes and the installation...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
SoftDevice: s140
--
Hi all,
I use ble_app_blinky example and Android nRF Blinky SDK( https://github.com/NordicSemiconductor...
During developpement of project on nRF52810, we used the nRF52DK PCA10040.
Since we wanted to use P0.9 and P0.10 (to limit differences between eval-board and real board...
I need to develop a ble advertising scanner with these requirements:
- capture at least 10 beacon advertisments (Eddystone TLM) continuously
- advertising interval of...
Hi,
I recently got the nRF51 Dongle for testing of a board with bluetooth interface. I am trying to get this dongle installed in Linux.
I found this link for the SDK...
Hi
I have a project need to be customized advertising frequency and scan in specific frequency
It means nrf52832 could broadcast at specific frequency and scanner also...
Dear Nordic Support,
I am using nRF52840 and BLE SDK v15.2. I want to control my nRF52840 through both UART CLI and BLE CLI so I try and read example: nRF5_SDK_15.2.0_9412b96...
Hello
I have a firmware with Softdevice S132 for NRF52 consists of main application (0x1F000 len:0x56000 ) and Bootloader (0x75000 len:0x9000). What I'm trying to do is...
Dear Nordic Team,
I am using a nRF52832 module purchased from Adafruit ( https://www.adafruit.com/product/3406 ) and I would like to connect it with another device with...
Hi there
First I tell you what I'm, trying to do...
I want to made a connection between a robot and a pc. Over this connection I want to program the robot with new software...
Hi,
I'm using nRF52832 SDK 14.2.0 s132 dfu, softdevice 5.0.0.
And i'm trying to update SD + BL + APP to SDK 15.3.0, softdevice 6.1.1.
When i update pakage by nRF connect...
Hi,
I am trying to upload HEX files to a nrf52832 (on a Sparkfun Breakout board) with a nRF52 DK. The problem is nRF Connect Programmer don't recognize them.
I installed...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
In sdk_config.h, BLE_ADVERTISING_ENABLED is not...
