Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have a simple central device where a gpio triggers the device to scan and connect to a peripheral. This is running ok on the PCA10040, and also on a separate hardware platform...
Using the latest version of Bluetooth low energy (V2.2.1) running on nRF Connect V2.6.2 I was never able to connect to a peripheral device.
The peripheral devices are based...
I'm using Nrf52840 as the MCU for my circuit board, now I need to use it to transmit audio data which is 16bit, 16KHz PCM format(mono channel, therefore 256 Kbps) to the external...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Ftwi_master_with_twis_slave_example.html
Testing
Test the TWIS slave and TWI master...
I followed the steps in Getting Started Assistant to load the asset_tracker application using SES(4.16) and it fails with the following error.
CMake Error at /Users/myfile...
Hello,
For ble communication in an application, I am usnig NRF52832 based boards. I am using ble_app_uart example for peripheral and ble_app_uart_c example for client. I...
I am using the nrf51422 development kit with sdk11. I am running the proximity application for the battery life service. I am inputting voltages ranging from 3000 millivolts...
SDK14.0.0/S132 5.0.0
The SDK provides an example of turning on SSP Debug mode for LE Secure connections
Is there a way to enable SSP Debug Mode for BLE Legacy Paired connections...
Hi , I have some issues with the ADC. When moving in and out from low power mode the ADC isn’t working correctly. I am using the nrfx_saadc driver. When moving to low power...
Hello Nordic Team,
I am using nRF52840 Dongle (PCA10059) and nRF5 SDK. I was tring to use PWM example code (PATH - "nRF5_SDK_15.3.0_59ac345\examples\peripheral\pwm_driver...
Hi.
I build application which is mix of writing QSPI to external NOR FLASH, using linkage list base on the fstorage FDS example all in the embOS (RTOS of Segger).
I have...
Hi all,
I using nrf52832 and segger IDE
I am trying disable softdevice and enable it while chip running. In my project, I use RTC1 for app timer.
When I disable SD,...
My setup:
- nRF52840 Preview DK (though i have tried this on a newer version too)
- 3.3V separate supply
- DMM (Agilent 34465A)
DK Connections:
- SW9 is set to...
Hi,
We are trying to take the nRF sniffer trace but there is some issue is showing , i will explain it below.
we are following nRF Sniffer "User Guide v2.2" for initialization...
Hey,
So I recently got some test SIMs from AT&T to use for our development. I'm trying to get them working with my nRF9160 dev kit but can't seem to get a connection to...
