Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
i tried to find an example with SPI which describes the connection between two nrf24LE1, one as master and one as slave, but i could not find anything. I need the following...
Trying the ATT_MTU Thourughput Example with SoftDevice:
nRF5_SDK_13.0.0-1.alpha_055eef3/components/softdevice/s140/hex/s140_nrf52840_5.0.0-1.alpha_softdevice.hex
on...
Hi, I just want to know,
Is it possible to develop a device that advertise normally and be connected by mobile, but the device must always send the eddystone-format advertising...
I'm interested in adopting nRF52840 as a mesh networking + Beacon device. It is my understanding that the Nordic SDK for mesh will only be released after Bluetooth SIG releases...
hello everyone:
I work IPv6 over BLE example on both Raspberry pi ,this pic is 6LN (CoAP Server)sending IPv6 over BLE packets to 6LBR(CoAP client) and I use tcpdump to...
Hi,
I'm testing the multi-link functionality.
I want to manage the connections with connection handler.
But, p_gap_evt->conn_handle passed thru on_ble_evt(); and p_ble_nus_evt...
Is it possible to setup the nrf52 with the HRS profile along with UART. I'd like to send heart rate date along with UART messages.
I'd also like to have an android app...
Hi all,
I have need to create BLE device with ability to securely store private keys and change those. According to presentation from ARM with assistance of CryptoCell and...
Hello, I wanna know where I can download it, if there is one at all?
I want both schmatic and pcb library file. I thought I can substitute and "make due" with nrf52832...
I'm using nRF52 + SDK11.0.0 + s132. I'm following this tutorial. I am able to build from the command line and from Eclipse just successfully. However, Eclipse is unable to...
Hi
I'm using nrf51822 with soft device 11.0 & want to read a 12 volt digital signal for this I'm converting 12v to 3v3 (4.5 & 1.5 Kohm Resistor) using voltage divider ckt...
I am using nrf51822 with soft device s130.I used sd_app_evt_wait() to enter the sleep mode and i disabled all the peripherals before enabling sleep mode.According to the datasheet...
I can't understand concept of control point..
Is it just one of charateristics?
So what are differences with other charateristics?
I heard that control point can...
I'm not sure if this question has been asked here before, but I couldnt find an existing answer...
I know that flash memory only has a relatively limited number of write...
What is the MDK? I am using Eclipse and GCC on Linux with the GNU ARM plugin for Eclipse. I need to upgrade from SDK12.0 to get the workaround for errata 108.
The release...
