Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I am trying to understand how to appropriately handle the Device Manager event of DM_EVT_SECURITY_SETUP_REFRESH as a peripheral.
This occurs when the user loses...
Hi, I wanted o increase the frequency at which heart rate is updated.
So I made the following change
#define HEART_RATE_MEAS_INTERVAL APP_TIMER_TICKS(300, APP_TIMER_PRESCALER...
Hey guys!
I am using your spi-master driver from the SDK 11 with the nRF52 chip. I am trying to read data from a MPU-9250 chip, and through my logic analysis, it seems...
Hi to all!
I've developed a board with NRF8001 on it and it works fine. But I've noticed a strange behavior. I use a mobile phone with NRF master control panel to work...
Dear All,
I am making IR transmitter using nrf51 where IR codes saved in SD card using PWM library we can transmitt the code while BLE is working.
Is it possible that...
Hi,
I am working on some application in which i have combined multiple profiles in one code.
In this i don't want generic access and generic attribute profiles to be displayed...
Hello.
I am using RTT successfully with nrf52 and IAR. But the start address for the RTT control block is a moving target: it changes whenever my code changes. I want to...
The product specifications publication for the nRF51822 doesn't list a gull wing chip pinouts found on the PCA10028 found on the evaluation board, kinda wondering if there...
Can someone confirm that all that needs to be changed to make code run with the SD installed is to change the linker to link to 0x1C000 instead of 0x00000 ?
To test, I...
I am playing with nrf51 DK. I used the following sample code,
devzone.nordicsemi.com/.../
ble_app_template_with_pstorage_SDK_8_1_0.zip
I want to pstorage clear/store...
I'm having an issue with secure BLE pairing, and once the problem shows up, it will not go away until I reprogram the SoftDevice. It persists through resets, so it must be...
I am currently using the nrf52 device for an application where when user's of my devices come close to one another, they automatically start sharing state information. There...
Hello all,
I currently have a test rig with 3 sensors, each with their own pin and interrupt they are supposed to carry out. Whichever two I put first in my gpiote_init...
Dear all,
I'm using SDk130 and the Software is based on the ble_app_uart_c example.
Now I want to scan the advertising data from a peripheral (device name, peer address...
