Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I'm currently developing a firmware running on nRF51-dongles (PCA10028). The dongle communicates with a PC application over UART. Everything is working fine except...
Hello we would like to use the Nordic chip to send wireless messages from a node to other nodes directly,without hubs. We wouldn't like to be limited to up to 8 nodes receiving...
Hello,
Setup: Android 4.4.2 (LG G2), nRF51822 peripherial.
I noticed that once in a while when trying to connect to my nRF51 based device it won't connect and what is...
softdevice 8.01,app is hts. ceilphone is HTC one. nrf tools.
add some functions display，adc, eg. use nrf tools HTM connect to the board, it's reboot every time when clip...
I'm using nrf51422, SoftDevice 310 and SDK 6.1.0, when i call sd_ppi_channel_enable_set, it causes SOFTDEVICE_NOT_ENABLED error, but softdevice was enabled earlier with SOFTDEVICE_HANDLER_INIT...
Dear all.
I have some test result on DFU feature. Please any comment on this issue.
test condition
Mater control panel (64-bit version)
nRFgo studio...
In my application, I had these lines.
nrf_gpiote_event_config(0, mPinDat, NRF_GPIOTE_POLARITY_LOTOHI);
nrf_gpiote_event_config(1, mPinDat, NRF_GPIOTE_POLARITY_HITOLO...
Hi,
On iOS, is there any way to download files right into the nRF Toolbox "User files" ?
This would be useful for DFU tests, to retrieve my binaries from the web.
For...
Hi everyone,
When I set the radio's transmit power, I can use "sd_ble_gap_tx_power_set" function. If I want to get the radio's transmit power, is there any function I can...
I am using NRF_GPIOTE->EVENTS_IN[0] and NRF_GPIOTE->EVENTS_IN[1] in my software. I had my own GPIOTE_IRQHandler working.
Today I am adding UART module into my source code...
Looking for a 3rd party Nordic based BLE module that comes with a chip antenna and exposed pin headers so I can quickly solder a AA battery housing and a single SPI board...
I'm using nRF51822 Beacon v1.1.0.
It seems interrupt has ocurred every 256msec.
I want to change timing of interrupt interval.(like a 512msec, 1024msec etc.)
Is it possible...
We're making a height sensor with Bluetooth connectivity using a simple HC-SR04 ultrasonic module, which outputs the height as a pulse with certain width. The width of the...
