Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
I compiled some legacy code (once written for the nRF52832), trying to adapt it for the nRF52805.
I have already done the following:
defining -DNRF52805_XXAA
defining...
Yesterday, I upgraded to nRF Connect for VS Code extension version 2026.6.2030 and restarted VS Code, and now no matter what I do, the 'Flash' button in my project just pops...
We use the NRF Mesh Android Library (and are developing with iOS version as well). An issue that we are running into on a small number of devices is that the library things...
Can I reduce the thermal pad size for the nRF52840 (aQFN)?
Currently the thermal pad is 4.85mm x 4.85mm, but in order to facilitate breaking out all the inner pads, reducing...
The nrf_cloud_multi_service sample sometimes appears to hang(appears to be a deadlock) shortly after successfully connecting and authorizing with nRF Cloud.
The log consistently...
Hi,
I am trying to program a custom board containing an nRF9151-LACA using the external programming interface (P20) on an nRF9151 DK. The board has never been programmed...
Hi --
We are in the process of setting up to flash a few hundred devices for our internal testing. We can currently flash to our board using nrfjprog either directly from...
I have a eval setup where I use the nrf52840 dongle with hci_usb flashed. It has a non-default config to enable DLE (this works fine).
I am sending buffers of 8192 bytes...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hi,
I have an application which is developed using nRF5 SDK version 17.1.0
Migrating to nRFConnect SDK is not an option at this stage of the project.
The application...
I'm stuck trying to set my nRF Connect extension on VSC. I've followed the guide for the installation but I'm reaching a wall. Every time I try to install a given SDK I have...
Hi all,
I am currently testing on nrf52dk (PCA10040, 3.0.0) with NCS v3.3. Note: I also tested with vanilla Zephyr and see the same issue.
The code I run is to 100% the...
Hello,
I previously opened a ticket describing an issue where using MCUBoot in NCS v3.1.0 caused the GRTC to reset after a sys_poweroff() .
As discussed in that ticket...
Hi everyone,
I'm evaluating the nRF54L15 for a very low-power sensor node application powered by a Lithium Thionyl Chloride (Li-SOCl₂) primary cell. The goal is to achieve...
Device : wearable IOT device
Battery capacity : Max 4.2V (Typ. 3.7V)
BLE Tx Power : Tx power is highest when the battery capacity is 4.2V (measured in air, not conduction...
