Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hello,
I have the Feeling with nrf connect programmer you can't select the Network core.
I use Programmer Version 2.2.0 and have our own hardware but also the nrf5340...
Hi Dev team,
I have been working with code development using Thingy91 and NRF Connect for Desktop. I use GitLab to maintain and manage my codebase.
I wanted to use GitLab...
I have nrf52840 pcb without xTAL.
In this ticket ticket I have discused about start Zephyr project without XTAL onboard.
But now I faced with other issue to start mcuboot...
Hi everyone,
I'm using nrf52840 as a connectable advertiser. Used ble_app_blinky example with some modifications. And I reduced the advertising interval to 2 seconds....
Hi, I'm using the example "libuartes" and developing 2 UARTE. But I dont know how to recoginize what port are communicating with external device because I only have 1 uart_event_handle...
Hi, Im trying to use nrfjprog from inside a docker container (ubuntu). I have started the container with --privileged and it seem to work but when i try to run the container...
Hello.
I use nRF52832 with SoftDevice and several TWI-connected IC's.
The power consumtion of nRF52832 is 14 uA after TWI initialization (low power mode and DC-DC regulator...
Hello, i have six buttons on my custom board, these buttons are inited with following code:
(there are pull up resistors present, hence NRF_GPIO_PIN_NOPULL is used)
SEGGER_RTT_printf...
Hello,
We are using nRF52840 chip for a power-sensitive application.
We use the UART which is connected to a LoRaWAN module.
Now when I enter the system ON mode after...
Hi,
I just started working with Zephyr and having some problems right out of the gate.
Board: Nordic nRF52840DK Example: i2c/spi_fujitsu_fram Branch: Main
When I'm using...
Can Nordic team be sure that SweynTooth test team has tested Nordic chips? If so, the claim in Nordic dev zone that Nordic chips are not listed indicating Nordic chips are...
I have followed Einar's response on the below thread but I still cannot see the logs on the SES
https://devzone.nordicsemi.com/f/nordic-q-a/79682/adding-mcuboot-bootloader...
Hey devs,
I'm trying to get the i2c interface to work with the MP8862. I followed the TWIS driver guide to get started and in there everything worked.
Now I wanted to...
Hi Everyone,
I'm using VS Code, nrfConnect SDK v1.7.0
I'm trying for minimal bluetooth roles(either central/peripheral) along dfu support in nrf52820 chipset.
when I...
Hello,
I recognized a wrong answer is sent by the ZigBee stack of nRF Connect 1.5.1 and 1.7.0 (and others).
Eg. the application provides a color control cluster as a...
