Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
52840 MAXIMUM_TX_POWER is 8dB,
it support long range transmission,see Test reports & deployment recommendations — Fanstel
5340 MAXIMUM_TX_POWER is only 3dB...
we are using "nRF5_SDK_17.0.2_d674dde" and nRF52832 chipset to develop software, after build via SES, we try to merge the app hex file and softdevice file, but it fails. ...
Hi,
We want to know more about DMA in I2C,
we are using TWI Master and Slave drivers as mentioned here in this blog https://devzone.nordicsemi.com/guides/nrf-connect...
I've been trying to build blinky using the nRF SDK from the toolchain manager with no success on windows 10. I've previously been able to build projects so I'm not entirely...
I would like to make my own project of an analog sensor with BLE feature. Is it a good idea to go with third party module (because of the easy availability of Antenna)? can...
Hi! I measure the micro frequency by Hantek Osiloskop in two-mode.
First, I use a simple Blink without softdevice , reaching 570kHz in 10us. Second, I use a ble_app_blinky...
Hi, I am looking for some help in interfacing STM32F4 MCU and nRF52832 module via UART for establishing BLE communication. My application needs both the devices.
I downloaded...
Hello everyone,
how can I implement a blacklist for my central which is scanning for a UUID and should also check for example device name. If the device name is in the blacklist...
We have developed a sensor application using ESB protocol with the nRF SDK (nRF52832 on Tx side and nRF52840 on Rx side).
We would like to redevelop now the receiver under...
Hi
1、I made the following modifications to the hello_world example（ncs1.7.0\v1.7.0\zephyr\samples\hello_world.
2、I have disabled uart0,But the average power...
Hi,
I'd want to implement RTC for regular testing of a variable. I am largely based on The BLE_uart exemple and have added a timer instance and a PWM instance. As the...
Hello,
I run a piece of code on NCS1.8.0 on nRF5340-DK, and it returns -35 when executing k_msgq_get()，b ut the same code runs on NCS1.5.0 and the k_msgq_get() function...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
Since I want to bond with Android, I have created a central code that summarizes the functions that I...
