I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hello,
is it possible to measure frequency from 1Hz up to 400kHz (50% duty cycle) on gpio pin having soft device enabled with Peripheral functionality? The measurement...
Hello,
I am using the RADIO peripheral to send BLE 4 advertising packets back and forth between 2 DK's (nrf52840 as transmitter, nrf52833 as receiver) following the radio...
Hi,
Nrf52 52840DK,SDK17 S140.
how to broadcasts continuous data? (Continuous broadcasting, with different data each time)
code as follows:
SDKs\nRF5_SDK_17.0.2_d674dde...
I have VSCode 1.63.0 (Universal) on macOS 12.0.1 with ncs v1.7.1 and a board with an nRF52840 MCU. I'm using the "hello_world" example. If I power cycle the board I can start...
Hi,
I'm trying to connect to hook-up a debugger in VSCode to my target but am unable to. The hardware is custom and JLink connects fine with nrfjprog to program and erase...
Hi,
I'm trying to ,create a development environment for Alexa gadget in nRF52832.
here is the thing which I'm using:
1. nRF connect for desktop version v3.9.1
2. Toolchain...
I had a Thingy91 that I think I bricked in trying to upgrade the firmware. I'm able to see the device in desktop programming, but it says erasing then gets to a 100% screen...
Dear, I am new to Nordic. I created a simple project for testing. There is a small fucntion to display "Hello World". After , Re-build Solution.. the memory used is as shown...
Dear community,
I am evaluating the nrf52 chip on the nrf52dk. I am using the peripheral_uart example, built for nrf52810. I have stumbled upon an error which I'm not sure...
In our BLE connections we often receive a BLE_GATTC_EVT_WRITE_RSP event with gatt_status 0x01F2.
Looking at the list of GATT_STATUS values, this must be an error in the...
Hi, based on my previous posts ( 2nd post , 1st post ) regarding the ble_app_uart_c multilink example I now face another issue.
When I run the multilink example on my nRF52840...
Hello,
Until now we compiled our company project using SEGGER Embedded Studio command line tool 'emBuild' that was called from a custom Makefile like this:
But we...
Hi all,
I want to self provision my node. I am using nrf52832 dev board, mesh SDK v 3.1.0, light switch client example. You may wonder why self provisioning, when there...
Hi, I am currently utilizing an app that supports multi link; however, I was only able to get 7 maximum stable connections. My goal for this multi-link is to connect a sensor...
